KitchenAid Dishwasher Tools needed for installation Parts supplied for installation, Panel A

Before you start... 11 Unlape and open washer lid. Remove packages and ho!ses from washer.

Check location where washer wrll be installed. Proper installation is your responsibilily. Make sure you have everylh’ln(

for correct inslallalion.

Grounded eleclrlcal outlet is ,’ required. See Electrical requiremenls.

Slandplpe			dram syslem:	Needs
a two-inch minimum diameter
slandpipe			with minimum-
carry-awaY
--..I	----I	of
capacity
17 gallons			per
minute.		Top 01
standpipe			must
be al least 34
72 inches			from	ObserveI
bottom		of
washer.
					all governlng
Floor	dram			ordinances.
No. 255320. d				j--/f

I.“. “la” .,“a” ..“a., m-1”“.-. 1.111. I

within 4 feet of Ihe beck 01 the washt and provide waler pressure 5-100 PSI.

IIII Leundry tub draln cyslem: Needs a 20.oallon laundrv tub. Too of lub must

1I be aI least 34 inches high’and no higher than 72 inches lrom botlom 01

washer./

		If a longer drain hose is keeded,
		drain hose (Part No. 366423) and
		hose extension kit (Part No.
		265442) are available	lrom
		KitchenAid-aulhorized	parts
1	/	dislributors.	/

SEERECESSED INSTRUCTIONS ON BACK COVER.

loor must be sturdy enough to

		waler		lo washer.
		Product	Damage
	Do Not store or operale
eve1 floor: Maximum slope	washer	below	32°F (some
nder 60,ti@ washer 1 inch.	waler	may remaln		In
	washer).
	See Use & Care Gulde for
	“Wlnlerlzlng” Informallon.
	Fellure lo follow above may
	resull	In pro&cl		damage.

Tools needed for installation:

Parts supplied for installation:

Remove parts horn packages. Check that all parts were included.

Sectrical ‘equirements

Eleclrlcal Shock Hazard

- Eleclrlcal ground Is required on lhls appliance.

l If cold waler plpe Is Interrupted by plasllc, non-metalllc gaskets or olher insulallng melerlals, Do Nol uss for groundlng.

. Do Not ground lo a gas pipe.

a Do Not modify Ihe power supply cord plug. II It does not fit the oullel, have a proper oullet Installed by a qualllied eleclrlclan.

*Do Not have a fuse In lhe neutral or groundlng clrcult. A fuse In lhe neutral or aroundlna clrcull could result In arieleclrlc~l shock.

-Do Nol use an exlenslon cord wllh

this appliance.

. Check wllh a quallfled eleclrlclsn If you are In doubt as to whether the appliance Is properly grounded.

Fallure lo lollow lhese lnslrucllons could result in serious Injury or death.

codes permll and a separate ,oundlna wire Is used. II Is commended lhat a quelllied eclrlclan delermlne that the oundlng path Is adequale.

!O-Voll. 60-Hz. AC-only, 15- or 20. npere fused electrical supply Is quired. (Time-delay luse or circuit eaker is recommended.) II is commended lhal a separate circuil rving only this applianoe be provided,

Recommended grounding method

For your personal safely, this appliance must be grounded. This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard. the cord must be plugged inlo a mating J-prong groundmg-type wall receptacle, grounded in accordance with National Electrical Code, ANSllNFPA 70.lalesl edition and all local codes and ordinances. See Figure 1. If a maling wall receptacle Is not available, it is the personal responsibility and obligalion of the customer lo have a properly grounded 3- prong wall receptacle inslalled by a qualified electrician.

Flgure 1

Panel A