9
8.Plug 3-prong plug into a grounded
3-prong outlet.
To avoid product damage when not using
the rotisserie, remove motor and store
indoors.Remove spit rod and forks. Store
out of reach of children.
Lighting the infrared(rotisserie) burner
1.Push in and tur n rotisserie burner knob
to “LITE”.
2.At the same time, push in both red
button (left hand side) and burner
igniter button (right hand side).You will
hear a “snapping”sound.
3.When infrared burner lights, release
the burner igniter button but continue
pressing the red button for another 5 to
10 seconds.
IMPORTANT:
If the rotisserie burner does not light
immediately, turn the burner knob to “OFF”,
wait 5 minutes before relighting.
Electrical Shock Hazard
Plug into a grounded 3-prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions
can result in death, fire, or
electrical shock.
WARNING

Manually lighting infrared burner

1. Remove the manual lighting extension
from inside the drip tray.
2. Attach a match to the clip.
3. Strike the match to light it.
4. Carefully hold the lit match close to the
infrared burner.
Using the smoker box(es)
Your grill may have one or two slide-out
smoker boxes that can be used with the
main grill burners or the rotisserie.
The smoker trays are designed for easy
use.After deciding which wood chips to
use, follow the instructions on wood chip
packaging.Small size chips or pellets are
recommended.
WARNING
Burn Hazard
Do not remove the smoker box
when grill is hot.
Doing so can result in burns.
1.Slide box and chip cover out of smoker
compartment.
2.Remove
cover from
box.Turn
cover over
and fill with
prepared chips.
3.Turn smoker box over and place over
chip cover.Hold cover and box together
and turn right side up.
4.Slide box and cover back into smoker
compartment.
Light the smoker burner(s) 5 minutes
ahead of time to start them smoking.The
specially-designed smoker will smoke the
food while the grill burners or rotisserie
cooks it.Keeping the hood closed as
much as possible will maximize the
smoking effect.
chip cover
smoker box
Using the rotisserie
For best cooking results, do not use main
grill burners when using the rotisserie.
The rotisserie system is designed to cook
food from the rear using intense, searing
infrared heat.
1.Remove warming shelf.
2.Mount rotisserie motor on the gr ill's
mounting bracket.Position it securely
into support bracket slots.
3.To load the spit rod, slide one of the
rotisserie forks onto the spit rod with
prongs facing away from handle.
4.Push spit rod through the center of the
food, then slide second rotisserie fork
into position.
5.Center the food and rotisserie forks on
spit rod and tighten wing nuts on the
rotisserie forks.If necessary, secure
loose food portions with butcher's
string only.
6.Once the food is positioned on spit rod,
place pointed end of rod into rotisserie
motor and lower spit rod onto supports
at either side of the grill.

IMPORTANT:On Model KBGS292LSS,

remove the handle

from the spit rod when

using the side burner.

The handle will get

“HOT”and failure to

remove it will cause

the handle to crack

and melt.

7.Plug single-prong plug into rotisserie
motor.
rotisserie
fork
motor spit rod
back infrared burner

Manually lighting the burners

1. Use a paper match to light the burners.
2. Push in and turn the burner knob to
“LITE” for the burner closest to the lit
match.The burner will light immediately.
IMPORTANT:
If burner does not light immediately, turn the
burner knob to “OFF” and wait 5 minutes
before relighting.

If any burners do not light after attempting

to manually light them, contact the

KitchenAid Assistance Center.

remove
handle
5. Push in and turn the infrared burner
control knob to “LITE”.
6. Push in the red button above the
infrared burner control knob, the burner
will light immediately.Hold this button
in for 5 to 10 seconds.
7. Repeat steps 3 through 6 for each
infrared burner.(Number of infrared
burners varies by model.)
8. Replace manual lighting extension
inside the drip tray.
IMPORTANT:
If the infrared burner does not light
immediately, turn the infrared burner
control knob to “OFF”and wait 5 minutes
before relighting.