57"
(144.8 cm)
27"
(68.6 cm)
33"*
(83.8 cm)
42"**
(106.7 cm)

PRODUCT MODEL NUMBERS OVERALL DIMENSIONS

EXHAUST VENTING

KHGV01R

Because Whirlpool Corporation policy includes a continuous commitment to improveour products, we reserve the right to change materials and specifications without notice.Dimensions are for planning purposes only. For complete details, see InstallationInstructions packed with product. Specifications subject to change without notice.Ref. 395765306-27-06

RECESSED AREA AND CLOSET INSTALLATION WITH OR WITHOUT PEDESTAL

UNDERCOUNTER INSTALLATION

A.Front viewB.Side viewC.Cabinet with vents
7"* (17.8 cm)
7"* (17.8 cm)
(12.7 cm) 33"
(83.8 cm)
1"
(2.5 cm)
5"
27"
(68.6 cm)
1"
(2.5 cm)
(2.5 cm)
1"
ABC

For closet installation, with a door, the minimum ventilation openings in the top and

bottom of the door are required. Louvered doors with equivalent air ventilation openings

in the top and bottom are acceptable.

1"
(2.5 cm)
1"
(2.5 cm)
42" min.
(106.7 cm)
27"
(68.6 cm)
1"
(2.5 cm)
Vent system chart 1 - rigid metal vent onlyVent system chart 2 - rigid metal vent used with a maximum of 8 ft (2.4m) flexible metal ventNumber of 90º turns or elbowsType ofventBox or louvered
hoods
Angled
hoods
0 Rigid metal 174 ft (53.0m) 168 ft (51.2m)1 Rigid metal 164 ft (50.0m) 158 ft (48.0m)2 Rigid metal 154 ft (46.9m) 148 ft (45.1m)3 Rigid metal 145 ft (44.2m) 139 ft (42.4m)4 Rigid metal 137 ft (41.8m) 131 ft (39.9m)Number of 90º turns or elbowsType ofventBox or louvered
hoods
Angled
hoods
0 Rigid metal 144 ft (43.9m) 138 ft (42.1m)1 Rigid metal 134 ft (40.8m) 128 ft (39.0m)2 Rigid metal 125 ft (38.1m) 119 ft (36.3m)3 Rigid metal 117 ft (35.7m) 111 ft (33.8m)
A. Louvered hood style
B. Box hood style
4"
(10.2 cm)
4"
(10.2 cm)
AB
4"
(10.2 cm)
2.5"
(6.4 cm)

Dimensions shown are for minimum spacing.

Recommended hood style

Angled hood style is

acceptable.

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns. Use the fewest

90°turns possible.

• Do not use vent runs longer than specified in vent length chart.

• Determine the number of elbows you will need.

Electrical:A 3 or 4 wire, single phase, 120/240

volt 60 Hz, AC only electrical supply (or 3 or 4 wire,

120/208 volt electrical supply, if specified on the

serial/rating plate) on a separate 30-amp circuit,

fused on both sides of the line. A time-delay fuse or

circuit breaker is recommended. Connect to an

individual branch circuit. Do not have a fuse in the

neutral or grounding circuit.

Exhaust venting:Exhaust your dr yer to the

outside. Four inch diameter vent is required. Rigid

or flexible metal exhaust vent must be used. Do not

use plastic or metal foil vent. Exhaust outlet hood

must be at least 12 inches from the ground or any

object that may be in the path of the exhaust.

Recommended installation

spacing for cabinet installation

For cabinet installation, with a door,

the minimum ventilation openings in

the top are required.

*Includes door handle**Includes feet extended 1" (2.5 cm)NOTE:Most installations require a minimum 5" (12.7 cm) clearance behind the dryer forthe exhaust vent with elbow.See InstallationsInstructions, “Venting Requirements.”Pro Line®Front-Loading Gas Dryer®
*Required spacingA.Front viewB.Side view - closet or confined areaC.Closet door with vents
AB
1"
(2.5 cm) 1"
(2.5 cm)
27"
(68.6 cm)
5"
(12.7 cm)
1"
(2.5 cm)
33"
(83.8 cm)
3"*
(7.6 cm)
3"*
(7.6 cm)
48 in.2*
(310 cm2)
24 in.2*
(155 cm2)
C