KitchenAid | Single Drawer Dishwasher Custom Door Panel Requirements |
® | |
| MODEL: KUDD01SSPA |
|
|
|
|
|
|
|
|
| 9” |
| ||
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| (22.9 cm) |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
cm) |
|
| CUSTOM |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| PANEL |
|
|
|
|
|
|
|
|
| |
|
| (Front Side) | ||||||||||
5⁄8” (39.7 |
|
| ||||||||||
|
| Center of |
|
|
|
|
| Medallion | ||||
15 |
|
|
|
|
| Location Area | ||||||
|
| Custom Panel |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 23 7⁄16” |
|
|
|
| |||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| |||||
FIGURE 1 | (59.5 cm) |
| ||||||||||
|
|
|
|
|
|
|
|
| ||||
25⁄16”
(5.9 cm)
5” (12.7 cm)
3)On the front side of the custom door panel, measure, mark and cut a hole for the medallion to size as shown (See figures 1 & 2).
NOTE: The medallion must be placed within the specified medallion area. Do not locate outside of this specified area (See figure 1).
4)Lay the custom door panel face down on a protective surface to prevent damage or abrasions.
5)On the backside of the custom door panel, rout a
1⁄4” (6.4 mm) radius around the medallion cutout previously cut in step #3. The medallion end does not need to
be routed.
6)If custom door panel material is not suitable to withstand damp conditions, seal with a moisture resistant material. For painted panel, paint all rear edges to improve sealing.
MEDALLION CUTOUT DIMENSIONS |
| Horizontal | ||||||
| Position Line | |||||||
| 1 |
| ⁄32” (32.6mm) MAX. |
| 1 7⁄16” | |||
| 9 |
|
| |||||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| (36.5 mm) | CUSTOM |
17⁄32” |
|
|
|
|
| ⁄4” (6.4 mm) |
| PANEL |
(30.8 mm) |
|
|
|
| 1 |
| (Back Side) | |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Vertical | Medallion |
|
|
|
| 13 |
|
| Location Area | |
|
|
|
| 1 ⁄64” |
|
| Center Line |
|
|
|
|
| (30.6 mm) | Medallion |
| ||
|
|
|
|
|
| |||
|
| 2 | ⁄32” |
| End |
|
| |
FIGURE 2 |
|
|
| 13 |
|
| FIGURE 3 |
|
(60.8 mm) |
|
|
| |||||
|
|
|
|
| ||||
IMPORTANT: It is recommended that the custom door panel be made from suitable material to withstand damp conditions or adequately sealed with a
1)Cut the custom door panel to size as shown
(See figure 1). The custom panel may be wider than
the dishwasher in order to match the surrounding cabinets.
NOTE: The minimum custom panel thickness is
5⁄8” (16mm). Panel thickness more than 11⁄16” (18mm) can be accommodated but overall product depth will increase accordingly.
2)On the front side of the custom door panel, measure and mark the location of the customer supplied handle. The location is customer preference. Do not install handle at this time.
7)On the backside of the custom door panel, measure and mark the vertical center line and horizontal position line (See figure 3).
NOTE: The 1 7⁄16” (36.5 mm) horizontal position line is marked for later use in the installation process. Refer to the Installation Instructions Single Drawer Dishwasher included with the Drawer Dishwasher to align and attach the custom door panel to the factory supplied metal plate.
8)Mount the customer supplied handle to the location previously marked on the custom panel.
IMPORTANT: When mounting the customer supplied handle, screws must fit flush to the panel and not extend beyond the back surface.
9)Refer to the Installation Instructions Single Drawer Dishwasher included with the Drawer Dishwasher to complete installation.
