KitchenAid W10300928C warranty Dishwasher Feedback Section, Canceling a Cycle

CONTROLS AND CYCLE STATUS

CONTROL PURPOSECOMMENTS

To start or resume a wash cycle

If the door is opened during a cycle or the power is interrupted, the Start/Resume indicator flashes. The cycle will not resume until the door is closed and START/RESUME is pressed.

NOTE: If the Start/Resume button is located on top of door, push door firmly closed within 3 seconds of pressing START/RESUME. If the door is not closed within 3 seconds, the Start/Resume button LED will flash, an audible tone will be heard, and the cycle will not start.

To reset any cycle or options during selection.

To cancel a wash cycle after it's started.

Press and hold CANCEL/DRAIN to reset any control selections made.

See “Canceling A Cycle After Dishwasher Is Started” and “Changing A Cycle After Dishwasher Is Started” sections.

	To turn the audible		Press and hold the Hi-Temp Scrub button for 3 seconds to turn the audible tones on or off.
	tones on or off.		Only audible tones for confirming button presses can be turned on/off. Important audible
			tones, such as indicating a cycle has been interrupted, cannot be deactivated.
			Dishwasher Feedback Section
CONTROLS AND CYCLE STATUS
CONTROL		PURPOSE		COMMENTS
		The Cycle Status Indicator		Clean indicator glows when a cycle is finished.
		Lights are used to follow the		If you select the Sani Rinse option, when the Sani Rinse cycle is finished,
		progress of the dishwasher
				the Sanitized indicator glows. If your dishwasher did not properly sanitize
		cycle. Located on the front
				your dishes, the light flashes at the end of the cycle. This can happen if the
		of the dishwasher for front
				cycle is interrupted, or the water could not be heated to the required
		control models, and located
				temperature.
		on the top of the door for
				The Clean and Sanitized lights go off when you open and close the door or
		hidden control models.
				press and hold CANCEL.
	A	The Front Indicator Light or		The light will be blue if the dishwasher is washing or rinsing. The light will
		Single Exterior Light (A)		be red when the dishwasher is drying. The light will be green to indicate
		shows progress of your		that the cycle is complete. If the Front Indicator Light is blinking, see
		dishwasher cycle by color.		“Troubleshooting” section.
		(Available on some hidden
		control models only).

The Cycle Status Display is used to follow the progress of the dishwasher cycle, and to show other information.

(Available on some models instead of Cycle Status Indicator Lights)

The indicators will inform you if you are able to add a dish to the cycle after it has started. It will also inform you if the dishwasher is washing, rinsing, drying, complete, and/or sanitized. They will show whether the control is locked and/or the delay option is selected. A series of bars will count down the duration of the cycle remaining from left to right. Each bar equals approximately 24 minutes of cycle length. The bars will also count down the delay feature from left to right, and the delay indicator will be activated.

Canceling A Cycle

1.Press and hold the Cancel/Drain button once. The Cancel/ Drain light will turn on. If the Cancel/Drain button is located on the top of the door, open the door slightly to stop the cycle. Wait for the spraying action to stop before completely opening the door. Press and hold the Cancel/Drain button once.

2.Close the door and the dishwasher starts a drain cycle (if water remains in bottom of dishwasher). Let the dishwasher drain completely. The Cancel/Drain light turns off after 2 minutes.

Changing A Cycle After Dishwasher Is Started

1.You can interrupt a cycle and restart your dishwasher from the beginning using the following procedure.

2.Press and hold the Cancel/Drain button twice to reset the control. If the Cancel/Drain button is located on the top of the door, open the door slightly to stop the cycle. Wait for the spraying action to stop before completely opening the door. Press and hold the Cancel/Drain button twice to reset the control.

3.Select new cycles and options.

4.Press START/RESUME.

Adding A Dish After Dishwasher Is Started

1.Check if Add a Dish indicator is lit. (Available on some models. Otherwise, proceed to Step 2.)

2.Open the door slightly to stop the cycle. Wait for the spraying action to stop, then open the door completely.

3.Check whether the detergent dispenser cover is still closed. If it is open, the wash cycle has already started and adding a dish is not recommended.

4.If detergent has not yet been used (detergent dispenser cover is closed), you may add a dish.

5.Press START/RESUME.

10