“SPEAKER IN” / ALL MODELS

For parallel connection of the subwoofer and main speaker wires (main speakers full range), connect the subwoofer input wires to the main channel, right and left, speaker outputs of your amplifier or to a secondary set of main speaker terminals (speaker B) if your amplifier is so equipped. Refer to Figure A. Alternately, you can connect the wires from your main speakers, along with the sub- woofer’s input wires, to the “SPEAKER IN” terminals on the subwoofer. This may be more conve- nient if the subwoofer is closer to your speakers than it is to your electronics. Please consult your dealer for details regarding connection of multiple speaker cables to a common set of speaker out- puts. For optimal performance, use equal lengths (left and right inputs) of the same high quality speaker cable that you are using to connect your main speakers. Consult your Klipsch dealer for recommendations. Refer to “About Speaker Wire Connections” for more detail.

“SPEAKER OUT” / KSW 12 AND 15

If a bass limited signal (high pass filtered) is being sent to your main speakers, connect them to the “SPEAKER OUT” terminals on the subwoofer instead of to your amplifier. Refer to the righthand side of Figure B. The high pass filter on these outputs will remove the bass frequencies below 100Hz from your main speakers, lowering distortion and increasing their dynamic range. Also refer to the “LOW PASS” section for more detail.

Note: Do not connect another subwoofer to these outputs as they are high pass filtered (bass

frequencies removed).

!

ABOUT SPEAKER WIRE CONNECTIONS

When making any type of speaker wire connection be sure to observe proper polarity (+ to + and - to -). If the polarity of one of the subwoofer input wires is reversed, the output of the subwoofer will be diminished. Most speaker wire is color-coded or has some distinguishing feature differentiating the two conductors. Speaker wire connectors on most loudspeakers and amplifiers are also color- coded. Typically, RED is positive (+) and BLACK is negative (-), or ground. It does not matter which wire conductor is connected to the positive or negative connection of your equipment as long as you are consistent. Be sure that the connections from the amp to all of the speakers in your system are connected in a like manner. If this is not done, the quantity of bass will be reduced and the stereo image will be compromised. Be careful to avoid excess bare wire or loose strands of wire at the con- nections. This could cause a shorting condition between adjacent positive and negative terminals, damaging your speakers and amplifier.

LINE LEVEL CONNECTIONS

These connections should be made using high quality shielded interconnect cables terminated with RCA phono plugs. These cables should be as short as possible and kept away from noise generating electrical equipment such as digital electronics or electric motors. Consult your Klipsch dealer for specific cable recommendations.

“LINE IN” / ALL MODELS

For best results, these jacks should be connected to a non-filtered (full-range) subwoofer or main channel pre-amp output on your receiver or pre-amp/processor. Refer to the lefthand side of Figure B. This input signal should contain the normal bass information present in the main left and right chan- nels. When connecting to a component that has only a single pair of pre-amp outputs, “Y” adapters (splitters) may be used to feed a signal to both the subwoofer and the power amplifier.

“LINE IN” / KSW 10 and 12 ONLY

You can connect a mono subwoofer output on your electronics to the “L/LFE” input using a single interconnect cable. If there is an inadequate amount of subwoofer volume even with the level control set to maximum, add a “Y” cord to the subwoofer end of the cable and connect to both line inputs. This will provide a significant (6dB) increase in the subwoofer’s output level.

“LINE OUT” / KSW 15 ONLY

If a bass limited (high pass filtered) signal is to be sent to your main speakers, connect the “LINE OUT” jacks on the subwoofer to the line level inputs on your main channel power amplifier.

Page 8 Page 10
Page 9
Image 9
Klipsch 20M0499 warranty Frequencies removed
Page 8 Page 10

20M0499 specifications

The Klipsch 20M0499 is an exceptional audio solution designed to deliver a robust listening experience across various environments. As part of Klipsch's esteemed line of products, this model showcases the brand's commitment to high-quality sound reproduction and innovative technologies.

One of the standout features of the Klipsch 20M0499 is its dynamic and detailed audio performance. Equipped with Klipsch's proprietary LTS (Linear Travel Suspension) tweeter, this device minimizes distortion and delivers crystal-clear highs, ensuring that vocal clarity and intricate details in music are perfectly preserved. The inclusion of an aluminum diaphragm also contributes to a lightweight yet durable construction, enhancing audio fidelity.

The dual 8-inch woofers in the Klipsch 20M0499 provide substantial bass output, making it an ideal choice for both music enthusiasts and home theater aficionados. These woofers are designed with a lightweight, rigid construction to improve response times and deliver deeper, more impactful low frequencies. The model’s ability to produce a rich soundstage allows for an immersive listening experience that brings movies and music to life.

Another significant characteristic of this model is the utilization of the Tractrix horn technology. This innovative design directs high frequencies more efficiently, creating a wider dispersion of sound throughout the listening area. As a result, it provides a more dynamic and engaging auditory experience, allowing for optimal sound quality regardless of positioning in the room.

The Klipsch 20M0499 also features an elegant and modern aesthetic that seamlessly blends with various décor styles. Its sleek cabinet design ensures that it not only sounds great but looks great too. Moreover, it comes equipped with high-quality connection options, allowing for easy integration with existing audio setups, whether wired or wireless.

Durability is another key aspect of the Klipsch 20M0499. Built with high-grade materials, it is designed to withstand the test of time while maintaining its structural integrity and performance levels. This commitment to quality ensures that users can rely on this model for years to come.

In summary, the Klipsch 20M0499 embodies advanced sound technologies coupled with a stylish and robust design. Its comprehensive feature set, including the LTS tweeter, Tractrix horn technology, and powerful woofers, makes it an outstanding choice for those seeking an elevated audio experience. Whether for casual listening or dedicated home theater use, the Klipsch 20M0499 is poised to exceed expectations.
Top Page Image Contents