OBTAINING THE CHEMICALS
Catalog numbers are as follows:
Product | Min/Mult | CAT Number | |
Order Qty | |||
|
| ||
|
|
| |
KODAK Negative Film | 2 | 801 7519 | |
Processing Cartridge | |||
FC1 |
|
| |
|
|
| |
KODAK Negative Film | 2 | 867 2701 | |
Processing Cartridge | |||
FC2 |
|
| |
|
|
| |
KODAK Rinse Tablets* | 4 | 191 3110 | |
|
|
| |
KODAK Negative Film | 1 | 833 9723 | |
FC Tank Developer | |||
|
| ||
|
|
| |
KODAK Negative Film | 1 | 107 2024 | |
FC Tank Bleach | |||
|
| ||
|
|
| |
KODAK Negative Film | 1 | 813 4421 | |
FC Tank Fixer | |||
|
| ||
|
|
| |
KODAK Negative Film | 3 | 872 4791 | |
FC Tank Rinse | |||
|
| ||
|
|
| |
*Used in water reservoir on processor |
| ||
SAFE HANDLING OF PHOTOGRAPHIC CHEMICALS
Handle all chemicals carefully. When you mix solutions, wear goggles or a face shield, a protective rubber apron, and protective gloves made with neoprene or nitrile rubber. Clean protective clothing after use to remove any chemical residue that can cause contamination. For more information about potential health hazards and safe handling of specific Kodak chemicals, see the label and the Material Safety Data Sheet (MSDS) for the chemical. Consult the MSDS for regional contact information. MSDS copies are available at the Kodak website at www.kodak.com/go/photochemicals.
CONVERTING TO THE KODAK
NEGATIVE FILM PROCESSING
CARTRIDGES
No processor adjustments are required to use KODAK Negative Film Processing Cartridges FC1 and FC2. These cartridges are designed to mix and replenish on top of existing solution. Use the same processor settings that you use with your current chemical cartridge. Standard conditions are shown in Figure 1 on page 3.
Preparing Fresh Working Tank Solutions
Use the following Kodak chemicals to prepare fresh working tank solutions:
Developer Tank (N1)
Use KODAK Negative Film FC Tank Developer
CAT No. 833 9723. Each kit makes 5.2 litres. Two kits are required for the FP363SC processor. Three kits are required for the FP563SC processor. Follow the directions in the following table:
Step | FP363SC | FP563SC | |
Processor | Processor | ||
| |||
| Mix 2 bottles of | Add 4 litres of water | |
| developer Part A | to processor | |
| with 2 litres of water | developer (N1) tank. | |
| in mixing bottle. Add | Then mix 3 bottles of | |
1 | solution to processor | developer Part A | |
| developer (N1) tank. | with 2 litres of water | |
|
| in mixing bottle. Add | |
|
| solution to processor | |
|
| developer (N1) tank. | |
| Mix 2 bottles of | Mix 3 bottles of | |
| developer Part B | developer Part B | |
2 | with 2 litres of water | with 2 litres of water | |
in mixing bottle. Add | in mixing bottle. Add | ||
| |||
| solution to processor | processor developer | |
| developer (N1) tank. | (N1) tank. | |
| Mix 2 bottles of | Mix 3 bottles of | |
| developer Part C | developer Part C | |
3 | with 2 litres of water | with 2 litres of water | |
in mixing bottle. Add | in mixing bottle. Add | ||
| |||
| processor developer | processor developer | |
| (N1) tank. | (N1) tank. | |
| Position tank level | Position tank level | |
| gauge on processor | gauge on processor | |
4 | developer (N1) rack. | developer (N1) rack. | |
Add water to N1 | Add water to N1 | ||
| |||
| level mark (about | level mark (about | |
| 2.3 litres). | 2.4 litres). |
2 | Using the KODAK Negative Film Processing Cartridges FC1 and FC2 • |
