AX3000G EasyStart
Step 2 has been changed from
The ESS settings are as follows:
| SMOOTH |
| STEPMODE |
| STEP1 | STEP 2 | STEP 3 | STEP 4 | STEP 5 | STEP 6 | STEP 7 |
|
|
|
|
|
|
|
|
|
|
|
|
| 0 |
|
| 0 | 4 | 7 | 12 | ||||
Pitch shifter: | Pitch=0, Fine=0, tracking=80, direct=0.0, effect=7.0 |
|
|
|
| ||||||
Delay: | 2 Tap Delay |
|
|
|
|
|
|
| |||
Time: 756, Feedback 4.4, Tone 7.9, | Tap Time 5.0, Mix 4.4 |
|
|
|
|
| |||||
Reverb: | Slap… Time=7.7, Lo Damp 3.7, High Damp 5.4, Pre Delay 0, Mix 4.5 |
|
|
| |||||||
The Control Switch
You can assign the control switch to function in a variety of ways. It can act as an on/off for your effects/amp/cab models; a tap tempo for modulation or delay, or even as a trigger for the ESS. Below is a list of the Control Switch functions. You can make the following settings independently for each program for extra flexibility!
Press the EXP/CTL button and use VALUE KNOB 5 to select the effect you want to control, and then press EXIT to return to Program mode…
Control Switch Effect On/Off: | Control Switch Effect Control: |
• “I/ON OFF” External Insert effect on/off | • “FLN TRIG” Activates Classic Flanger LFO |
• “P/ON OFF” | • “HOLD DLY” Activates HOLD of Hold Delay |
• “A/ON OFF” Drive/Amp model on/off | • “FREEZ” Activates Freez of Freez effect |
• “M/ON OFF” Modulation effect on/off | • “ESS CTL1” Turn ESS on/off |
• “D/ON OFF” Delay effect on/off | • “ESS CTL2” Turn the effect being controlled by ESS on/off |
• “R/ON OFF” Reverb effect on/off | • “ESS TAP1” Tap tempo to specify the time between each |
| sequence step |
Control Switch Tap tempo: | • ESS TAP2” Tap tempo to specify the time between step 1 and the |
• MOD TAP” Modulation TAP TEMPO | last step of the sequence. |
• DLY TAP” Delay TAP TEMPO | • “ESS TRIG” Restart step sequence from step 1 |
!ESS TAP1, ESS TAP2, and ESS TRIG will do nothing if the SPEED of the step effect is set to PEdL.
Restoring the Factory Preset Programs
Here’s how you can restore the AX3000G’s programs and settings to the state in which it was shipped from the factory:
1.While simultaneously holding down the ▲/▼ buttons and the EXIT switch,
!If at this point, you decide that you really don’t want to execute this operation, press the EXIT switch.
2.Press the WRITE button. The name display will show “LOADING,” and the factory data will begin reloading.
When completed, the name display will indicate “COMPLETE,” and the AX3000G will automatically switch to Program Select Mode.
!If there are any settings you want to keep, you should first use the Backup Program Data function (programs can also be saved via our free AX3000G Editor/Librarian software; available at www.korg.com/AX3000G), or write down your settings using the Original Value icon. See the AX3000G Owner’s Manual for additional information on using the Backup Program Data function/ Original Value icon.
For more information, see your AX3000G Owner’s Manual, and be sure to visit www.korg.com/AX3000G for more tips and tricks!!
5
