VS-1616D HDMI I/O Card Installation Sheet
The
WARNING: An input card must only be mounted in a slot designated for input cards (slots 1 to 4 and 9 to 12) and an output card must only be mounted in a slot designated for output cards (slots 5 to 8 and 13 to 16).
To install an I/O card:
1.Power off the
2.Using a Phillips screwdriver, loosen the
screws at the top and bottom of the blanking plate.
3. Remove the blanking plate from the slot and store it for possible future use.
4.Remove the new card from its shipping box and
C |
|
|
|
|
T |
|
|
|
|
RL |
|
|
|
|
| I |
|
|
|
| N |
|
|
|
| I |
|
|
|
| N |
|
| |
|
|
| I |
|
RS232 |
|
|
| N |
|
|
| I | |
|
|
|
| |
|
|
|
| N |
NET | POWER |
|
|
|
C | LINK |
|
|
|
|
|
|
| |
T |
|
|
|
|
RL |
|
|
|
|
| HD |
|
|
|
| MI |
|
|
|
| HD | MI |
|
|
| IN |
|
| |
|
| D |
| |
| 1 |
| VI | |
| 2 |
|
| |
| IN |
|
| DL |
| 3 |
|
| |
| 4 |
| IN |
|
|
|
|
| |
|
|
| 5 |
|
|
|
| 6 | IN |
|
|
|
| |
|
|
|
| 7 |
|
|
|
| 8 |
|
|
| O | UT |
|
|
|
|
O |
|
|
|
|
|
|
|
|
|
|
UT | O |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| UT | O |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
|
|
| UT |
|
|
|
|
|
|
|
|
|
| O |
|
|
|
|
|
| |
|
|
|
| UT |
|
|
|
|
|
|
|
|
|
|
| I |
|
|
|
|
|
|
|
|
|
| N |
|
|
|
|
|
|
|
|
|
|
|
| I |
|
|
|
|
|
|
|
|
|
| N |
|
|
|
|
|
|
|
|
|
|
|
| I |
|
|
|
|
|
|
|
|
|
| N | |
DVI |
|
|
|
|
|
|
|
|
|
|
O | DVI |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
UT |
| D | VI |
|
|
|
|
|
|
|
1 |
|
|
|
|
|
|
|
| ||
2 | O |
|
|
|
|
|
|
|
| |
| UT |
| DL |
|
|
|
|
|
|
|
| 3 |
|
|
|
|
|
|
|
| |
| 4 | OU |
|
|
|
|
|
|
|
|
|
| T | D | VI |
|
|
|
|
| |
|
| 5 |
|
|
|
|
| |||
|
| 6 | OU |
|
|
|
|
|
| |
|
|
| T |
|
|
|
|
|
| |
|
|
| 7 |
|
| DVI |
|
|
| |
|
|
| 8 | IN |
|
|
|
| ||
|
|
|
|
|
|
| D |
| ||
|
|
|
| 9 |
|
|
| VI | ||
|
|
|
| 10 | IN |
|
| |||
|
|
|
|
|
|
|
| DL | ||
|
|
|
|
|
| 11 |
|
|
| |
|
|
|
|
|
| 12 |
| IN |
|
|
|
|
|
|
|
|
|
| 13 |
|
|
|
|
|
|
|
|
|
| 14 |
| IN |
|
|
|
|
|
|
|
|
|
| 15 |
|
|
|
|
|
|
|
|
|
| 16 |
U | T |
9 | |
10 |
|
O |
|
|
|
|
|
UT | O |
|
|
|
|
|
|
|
|
| |
| UT |
| O |
|
|
|
|
|
|
| |
|
|
| UT |
|
|
|
|
| TE |
| |
|
|
|
| ST | |
|
|
|
|
| RESOLUTION |
|
|
|
|
| PATTERN |
HD |
|
|
|
|
|
MI |
|
|
|
|
|
O | DVI |
|
|
|
|
UT |
| DL |
|
| |
11 |
|
|
| ||
12 | O |
| T |
|
|
|
|
|
| ||
| UT |
| ES |
| |
| 13 |
|
| T | |
| 14 | OU |
|
| |
|
| T |
|
| |
|
| 15 |
|
| |
|
| 16 |
|
|
|
HDMI
OUT
HDMI
5. Holding the card by the upper and lower handle, align the card with the plastic guide rails.
6. Slide the card into the chassis until the front of the card makes contact with the connector inside the chassis.
7. Press the card firmly into the slot until the connector plate is flush with the rear panel of the chassis and the connector is fully seated.
8. Using a Phillips screwdriver, tighten the retaining screws at the top and bottom of the card to secure it to the chassis.
9. Power on the
10. Power on the peripheral devices.
Kramer Electronics Ltd.
(P/N: