Wireless Thermometer
Model: 308-1910 Instruction Manual
View temperature with a glance. Precise
SETUP INSTRUCTIONS STEP BY STEP
STEP 1:
•Ensure that the transmitter is within 10 feet of the Wireless Thermometer.
• Remove battery cover from TX19 transmitter.
•Insert 2 new AAA batteries (not included) into the transmitter. Observe the correct polarity.
STEP 2:
• Remove battery cover from the Wireless |
Thermometer (follow the arrow on the bottom of the battery |
cover). |
TROUBLE SHOOTING
•If the Wireless Thermometer does not display the outdoor temperature after 3 minutes, remove the batteries from both units and repeat the setup process.
•From normal display, hold the UP ARROW button for 3 seconds to search for the outdoor temperature transmitter.
•For optimal 433MHz signal reception, the outdoor transmitter should be placed within 100 feet (30 meters) from the indoor Wireless Thermometer.
The outdoor temperature reception icon will flash:
•During initial setup, for up to three minutes, until it connects with the transmitter.
•About every minute afterwards as the wireless thermometer receives an update.
•When the UP ARROW button is held for 3 seconds to begin a search for the transmitter.
SET TIME
In Time mode, hold the TIME button for 3 seconds to set the time.
•HOUR: The Hour will flash. Press and release the ARROW buttons to select the correct hour. Press and release the TIME button once to move to the minutes.
•MINUTES: The Minutes will flash. Press and release the ARROW buttons to select the correct minutes. Press and release the TIME button once more to exit the program menu.
SELECT THE TIME AND TEMPERATURE FORMAT
The Thermometer either defaults to °C with 24 hr. time or °F with 12 hr. time. Both set up instructions are below:
LOW BATTERY ICON
The low battery icon will show above the outdoor temperature when it is time to change batteries.
MAXIMUM/MINIMUM TEMPERATURE READINGS
VIEW: Press and release the MIN/MAX button once to show the maximum temperature records. Press and release the MIN/MAX button again to view the minimum temperatures. Press and release the MIN/MAX button a third time to return to current temperature.
RESET: Hold the MAX/MIN key for 2 seconds to manually clear all the MIN/MAX records.
ALARM SET
From Time mode, press and release the ALARM button to switch to Alarm Mode. The letters “AL” will appear between the hours and the minutes. In Alarm Mode hold the ALARM button for 3 seconds to enter alarm set mode.
•HOUR: The Hour will flash. Press and release the ARROW buttons to select the correct hour. Press and release the ALARM button once to move to the minutes.
•MINUTES: The Minutes will flash. Press and release the ARROW buttons to select the correct minutes. Press and release
the ALARM button once more to exit the program menu.
Note: When the alarm sounds, it continues for 2 minutes and then shuts off completely.
SNOOZE
• When the alarm sounds, press the SNOOZE button to silence the |
alarm for 5 minutes. The alarm icon will flash. |
• | Insert 2 new AAA batteries (not included) into |
| the back of the Wireless Thermometer. |
| Observe the correct polarity (see marking |
| inside the battery compartment). |
• | Within 3 minutes, the Wireless Thermometer |
| will show readings in the outdoor temperature |
| area on the wireless thermometer. |
| Note: Allow the Wireless Thermometer and |
| the transmitter to stay within 10 feet of each |
| other for the first 15 minutes of set up. |
• | Do Not Mix Old and New Batteries |
• | Do Not Mix Alkaline, Standard, Lithium or Rechargeable |
| Batteries |
CELSIUS DEFAULT
•Default temperature reading is in Celsius.
•From Time mode, press and release the °F/°C button to select Fahrenheit temperature readout.
24 HOUR TIME
•Default time format is 24 hour time format.
•From Time mode, press and release the 12/24h button to select 12 hour time readout.
FAHRENHEIT DEFAULT
•Default temperature reading is in Fahrenheit.
•From Time mode, press and release the °F/°C button to select Celsius temperature readout.
12 HOUR TIME
•Default time format is 12 hour time format.
•From Time mode, press and release the 12/24h button to select 24 hour time readout.
• | The snooze function can be repeated. |
• | Press any other button to turn the alarm off for 24 hours. |
ACTIVATE/DEACTIVATE ALARM
From Time mode, press and release the ALARM button to switch to Alarm mode. The letters “AL” will appear between the hours and the minutes.
ACTIVATE: In Alarm mode, press and release the UP ARROW button to activate the alarm. The alarm icon will appear.
DEACTIVATE: In Alarm mode, with the bell icon visible, press and release the UP ARROW button to deactivate the alarm. The bell icon disappears.