Optional Equipment Assemblies, Locking Bar | Land Pride BH2585

Table of Contents

Section 1 Assembly and Set-Up

Land Pride

Optional Equipment Assemblies

Locking Bar

Refer to Figure 1-13:

1.After the backhoe is attached to the tractor in working position proceed with the following steps to install the locking bar.

2.Assemble eyebolts (#7), lockwashers (#4) and nuts (#2) as shown. Do not tighten.

3.Install pins (#5) through eyebolts (#7) with the eyebolts being located the inside of backhoe lower link brackets. Secure pins in place with lynch pins(#6).

4.Adjust the 3/4” bolt against the tractor drawbar link.

5.Tighten eyebolts with nut and jam nut.

Ripper Tooth

Refer to Figure 1-14:

1.Remove bucket link (#1) by removing pin (#8) and roll pin (#7) and sliding out links (#2).

2.Assemble ripper tooth assembly with pins and links from step 1 as shown.

When the ripper tooth is not needed, the complete ripper assembly does not need to be disassembled. Remove pin (#9) and slide the ripper tooth (#3) out and store pin (#9) back in it’s previous location. The ripper tooth link

(#4) can now be used in place of the bucket link (#1).

Tractor’s Lower 3-point

mounts here

Locking Bar Assembly

Figure 1-13

20598

Ripper Tooth Assembly

Figure 1-14

16

10/28/05

Image 18

Land Pride BH2585 manual Optional Equipment Assemblies, Locking Bar, Ripper Tooth

Contents

Backhoes Table of Contents Be Aware Signal Words Important Safety InformationLook For The Safety Alert Symbol For Your Protection Transporting the Loader and Attachment Use Safety Lights and DevicesTransport Machinery Safely Keep Riders Off Machinery Wear Protective Equipment Practice Safe MaintenancePrepare for Emergencies Avoid High Pressure Fluids Hazard 838-380C 838-378C 838-379C 818-339C 839-933C 839-932C Owner Assistance Using This ManualApplication Serial Number Plate Backhoe Operation, Maintenance & Safety Tips Tractor Requirements Power Beyond Hydraulic SystemsAssembly and Set-Up Skid Steer Requirements Power Beyond & Closed Center Kit Closed Center Hydraulic Systems Choose the Appropriate Hosing Independent PTO Hydraulic Pump System Backhoe Independent Hydraulic Systems Mounting The Backhoe For All TractorsFor John Deere Tractors Main Frame Boom Cylinder Inside Boom Stabilizer Cylinder Lower Link Hitch Bracket Installation Transport Lock Backhoe Stabilizer Kit Installation Seat Assembly Bucket InstallationSkid Steer Hook-Up Optional Equipment Assemblies Locking BarRipper Tooth Transporting The Backhoe Preparing For OperationOperating The Backhoe Operating Instructions Control Functions BoomDipper Stick And Bucket Observe the following cautions while digging Digging SuggestionsDigging at the Correct Angle Dipper Stick & Boom Angle Bucket Angle Maintenance and Lubrication MaintenanceBucket Tooth Replacement Storage Bucket Pivot End of Stick LubricationBucket Pivot Bucket Cylinder Base End Boom Pivots Both Sides Dipper Stick Cylinder Base EndBoom Cylinder Rod End Boom Pivot Unerneath at end of Boom Stabilizer Arms Both Sides Boom Cylinder Base EndStabilizer Cylinder Rod End Both Sides Boom Swing Pivot Boom Swing Cylinder Rod End Both Sides Boom Swing Cylinder Base End Speciﬁcations and Capacities BH25 Series BackhoesBH2585 Features and Beneﬁts Features Benefits Troubleshooting Hydraulic System Problem Cause SolutionLoad drops when valve Performance In-tpi Torque Values Chart For Common Bolt SizeAppendix · m Ft-lb Mm x pitch Warranty Corporate Ofﬁce P.O. Box Salina, Kansas 67402-5060 USA