Lantronix 485 3.18 Defaults , 3.19 Exit Configuration Mode

Device Installer

Generally, one of two situations applies:

Encrypted NET485-to-NET485 communication. Be sure to configure both NET485 devices

with the same encryption key.

Third-party application to NET485-encrypted communication: NET485 uses standard AES

encryption protocols. To communicate successfully, products and applications on the peer

side must use the same protocols and the same encryption key as the NET485.

Lantronix Secure Com Port Redirector provides an encrypted connection from Windows-based

applications to the NET485. Information about SCPR is at

http://www.lantronix.com/device-networking/software-services/scpr.html

Note: Developers can license the Lantronix Encryption Library Suite. See http://www.lantronix.com/device-

networking/utilities-tools/.

3.17.10 Enable Enhanced Password

This setting defaults to the N (option), which allows you to set a 4-character password that protects the

Configuration Menu via Telnet and Web pages. The Y (Yes) option allows you to set an extended security

password of 16-characters for protecting Telnet and web page access.

3.17.11 Disable Port 77F0 (Hex)

Port 77F0 is a setting that allows a custom application to query or set the three NET485 configurable pins

when they are functioning as general purpose I/O (GPIO). You may want to disable this capability for

security purposes. The default setting is the N (No) option, which enables GPIO control. The Y (Yes) option

disables the GPIO control interface.

Note: The function of the configurable pins on the NET485 should be changed with caution. Some of the configurable

pins are not connected or used for other functions.

3.18 Defaults

Select 7 to reset the unit’s Channel 1 configuration, E-mail settings, and Expert settings to the default

settings. The server configurations (IP address information) remain unchanged. The configurable pins’

settings also remain unchanged.

3.19 Exit Configuration Mode

• Select 8 to exit the configuration mode without saving any changes or rebooting.

• Select 9 to save all changes and reboot the device. All values are stored in nonvolatile memory.

3-44 NET485 User Guide

Contents

Main NET485 RS422/485 Serial to Ethernet Adapter Page Copyright and Trademark Grid Connect Technical Support Disclaimer and Revisions Warranty Table of Contents Page List of Figures List of Tables Page 1. NET485 Overview 1.1 Overview 1.2 Overview of RS422 / RS485 1.2.1 The RS485 Enable Signal 1.2.2 NET485 Wiring Overview NET485 User Guide 1-3 D R U2 U4 1.3 RS422 / RS485 Network connections 1.3.1 RS422 Networks Overview 1.3.2 RS485 Networks NET485 User Guide 1-5 Figure 3 - RS485 Network Page 2. Introduction 2.1 Protocol Support 2.2 Serial RS422/485 Interface 2.3 Power Supply 2.4 Ethernet Interface 2.5 Product CD 2.6 Additional Documentation 2.7 Technical Specifications 3. Device Installer 3.1.1 Microsoft NET Framework 3.1.2 Install Device Installer 3.1.3 RUN Device Installer 3.1.4 Device Found 3.1.5 Assign IP 3.1.6 Assignment 3.2 Using Device Installer 3.2.1 Viewing the Current Configuration Device Installer 3-6 NET485 User Guide 3.3 Configuration Using Web Manager 3.3.1 Accessing XPort Using Device Installer 3.4 Network Configuration 3.4.1 Automatic IP Address Configuration 3.4.2 Static IP Address Configuration 3.4.3 Ethernet Configuration 3.5 Server Configuration 3.6 Host List Configuration 3.7 Channel 1 Configuration Device Installer Port Settings NET485 User Guide 3-13 Pack Control Flush Input Buffer (Serial to Network) 3.7.1 Connection Settings - TCP Device Installer 2. In the available fields, enter or modify the following information: Connect Protocol NET485 User Guide 3-15 Connect Mode: Passive Connection Connect Mode: Active Connection Endpoint Configuration Disconnect Mode 3-16 NET485 User Guide 3. When you are finished, click the OK button. 4. On the main menu, click Apply Settings. 3.7.2 Connection Settings - UDP 3.8 Email Settings 3.8.1 Trigger Configuration 3.9 Configurable Pin Settings 3.10 Apply Settings 3.11 Apply Factory Defaults 3.12 Configuration Using Telnet 3.12.1 Telnet Connection Device Installer 3.12.2 Telnet Messages 3-22 NET485 User Guide 3. The window displays: Device Installer Figure 10 - Setup Mode Window NET485 User Guide 3-23 3.13 Server Configuration (Option 0 Network Configuration) 3.13.1 IP Address 3.13.2 Set Gateway IP Address 3.13.3 Netmask: Number of Bits for Host Part Table 5 - Netmask Examples Netmask Host Bits 3.13.4 Change Telnet configuration password 3.13.5 DHCP Naming 3.14 Channel 1 Configuration (Serial Port Parameters) 3.14.1 Baudrate 3.14.2 I/F (Interface) Mode 3.14.3 Flow 3.14.4 Port Number 3.14.5 Connect Mode Table 10 - Connect Mode Options Connect Mode Option 7 6 5 4 3 2 1 0 Page Page Page Page 3.14.6 Send the Escape Sequence (+++) in Modem Mode 3.14.7 Auto Increment Source Port 3.14.8 Remote IP Address 3.14.9 Remote Port 3.14.10 DisConnMode 3.14.11 Flush Mode (Buffer Flushing) 3.14.12 Pack Control 3.14.13 DisConnTime (Inactivity Timeout) 3.14.14 Send Characters 3.14.15 Telnet Terminal Type 3.14.16 Channel (Port) Password 3.15 E-mail Settings 3.15.1 E-mail Setup 3.15.2 Trigger Setup 3.16 Expert Settings 3.16.1 TCP Keepalive time in seconds 3.16.2 ARP Cache timeout in seconds 3.16.3 Enable High Performance 3.16.4 Disable Monitor Mode at Bootup Page 3.17 Security Settings 3.17.1 Disable SNMP 3.17.2 SNMP Community Name 3.17.3 Disable Telnet Setup 3.17.4 Disable TFTP Firmware Upgrade 3.17.5 Disable Port 77FE (Hex) 3.17.6 Disable Web Server 3.17.7 Disable Web Setup 3.17.8 Disable ECHO Ports 3.17.9 Enable Encryption 3.18 Defaults 3.19 Exit Configuration Mode 4. Monitoring the Network 4.1.1 Entering Monitor Mode via the Network Port 4.1.2 Monitor Mode Commands Page 5. Updating Firmware 5.1 Obtaining Firmware 5.1.1 Reloading Firmware 5.1.2 Via Device Installer Page Troubleshooting 6. Troubleshooting NET485 User Guide 6-1 6.1.1 Problems and Error Messages Problem/Message Reason Solution Problem/Message Reason Solution Troubleshooting 6-2 NET485 User Guide 7. Binary to Hex Conversion 7.1.1 Conversion Table 7.1.2 Scientific Calculator