Lasko 5591 manual Modelo, TIMER FUNCTION Figure, Oscillation, OPERATION Figures 1 through

MODEL 5591

MODELO 5591

OPERATION (Figures 1 through 3)

The Heater may be operated by the manual controls located on the Heater (as shown in Figure 1) or by your remote control (shown in Figure 4).

1.Carefully remove the Heater from the bag and the carton.

2.Place the Heater on a firm, level surface.

WARNING: Plastic or rubber tabs, like the feet on this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces.

3.	Plug the cord set into a 120 V~ electrical outlet. Be sure plug
	fits tightly in outlet. A loose fit will cause overheating and dam-
	age the plug. Plug and cord set may feel warm during normal
	usage.
4.	When the Heater is initially plugged in, the red light will come
	on indicating that there is power to the unit. The red light
	will remain lit until the Heater is unplugged from the electrical
	outlet.
5.	Turn the Heater ON by touching the Power Icon (	) .
6. When initially turned on, the Heater will display the cur-
	rent room temperature in º Fahrenheit. Touch the (		) and (	)
	icons at the same time to change the display to		º Celsius.
	Touching the same icons again will change the display back to
	º Fahrenheit.The Heater will reset to º Fahrenheit after being
	unplugged.
7.	Upon turning the Heater on, the unit will be in HIGH heat ( ) (1500

TIMER FUNCTION (Figure 2)

The timer function will work in any mode. The timer function al- lows you to set the length of operation from 1 hour to 8 hours.

Touching the Timer Icon () will increase the length of operation by 1 hour each time the button is touched. Touching the Timer

Icon () once more after the display reflects 8 hours will reset the Heater to continuously running. Once the timer has been set, the timer will count down the hours in 1 hour increments, showing on the display the remaining operating time. The Heater will turn itself off when the set time has elapsed. The unit can be turned back by touching the Power Icon ().

Timer Function in	Timer Function in
	High Heat and Automatic
Low Heat	Temperature Control

Figure 2

AUTOMATIC TEMPERATURE CONTROL (Figure 3)

ARMADO (Figuras 1 a 4)

Herramientas Necesarias: Destornillador de Cabeza #2 Phillips (no incluido)

Retire cuidadosamente el Calefactor de su bolsa y caja.

Para facilitar el armado, coloque el Calefactor de manera que la parrilla frontal y el panel de control den hacia arriba.

(4) - M5 X 13mm (2) - M4 X 13mm

Tamaño Real De Tornillos

Figura 1

1.Arme la base enclavando las Protuberancias en los Orificios para Protuberancias. (Figura 2)

2.Fije las mitades de la base con (2) tornillos M4 X 13 mm. Pase el Cable Eléctrico por el gran orificio que se encuentra del Conjunto de la Base. NOTA: El Canal Para Cable en la parte inferior de la base debe estar hacia la parte posterior del Calefactor.

(Figura 3)

Canal Para

Cable

Cable

Eléctrico

Conjunto de

la Base

Figura 3 (2) - M4 X 13mm

	Watts) and will display the current room temperature.
	(Figure 1)	) Icon at this point will set the Heater into Low
8.	Touching the (
	heat mode.	) Icon once more will set the Heater into High
9.	Touching the (
	heat mode.

10.To turn the Heater OFF, touch the Power Icon () and unplug the unit from the electrical outlet.

Display when initially turned on

The automatic temperature function will only operate on "High" heat ( ). You cannot set the temperature automatically when the unit is in the low heat mode.

1. To set the room at a specific temperature touch the () or ( ) icons to the desired temperature. The display will now reflect the () and the temperature will be flashing. The Heater is now in Auto Temperature Mode.

2. When you reach the temperature at which you want to set the

unit, the set temperature will flash several times and then the

display will return to indicate the current room temperature and

will gradually change as the room temperature changes. NOTE:

the temperature display does not indicate the temperature of

the heated air being emitted by the heater.

Protuberancias

3.Alinee el Conjunto de la Base con el Conjunto de Soporte de Columna. Cerciórese de que la Muesca de Ubicación en el Conjunto de Soporte de Columna quede alineada con la Llave en el Conjunto de la Base (Figura 4). Una el Conjunto de la Base al Conjunto de Soporte de Columna con (4) tornillos M5 X 13 mm. Jale suavemente el Cable Eléctrico para que no quede holgado, y colóquelo en el Canal Para Cable del Conjunto de la Base.

Figure 1

3.	Once the room temperature reaches 2 degrees above the set
	temperature, the Heater will shut off. Once the room tempera-
	ture reaches 1 degree below the set temperature, the Heater
	will turn back on and continue to cycle off and on to maintain
	the set temperature.
4.	This function will cancel if the icon is touched.

Automatic air sampling feature: Functions only when the heater

is set in the automatic mode. It is normal for the heater fan to run for approximately 15 seconds after the heater has reached the set temperature. From this point on, the heater fan will turn on every 10 minutes for 10 seconds until the room requires additional heat.

Display reflects High Heat and

Automatic Temperature Control Function

Conjunto de

la Base

Orificios

Llave para

Protuberancias

Figura 2

Canal Para

Cable

Cable Eléctrico

OSCILLATION

Touching the Oscillation Icon () will allow the Heater to oscil- late back and forth. To stop the oscillation, touch the Oscillation Icon () again. When the Heater is in Automatic Temperature Control, the oscillation function will stop when the set tempera-

ture is reached and resume when the Heater turns back on.		Figure 3
Rev. B 6/10	4	5591ES

Figura 4

Rev. B 6/10 9 5591ES