MODELO 754200
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce the risk
of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Heater.
1.ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO NOT plug Heater into any other cord connected device, such as a power strip, surge protector, multiple outlet adapter, cord reel or
WARNING: Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that heater plug fits tightly into outlet before each use. During use, check to make certain the Heater plug is not overheating. If necessary have a qualified electrician check and/or replace the wall outlet.
2.Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons.
3.Make certain that the room is equipped with a working smoke detector.
4.Make certain that the power source conforms to the electrical requirements of the Heater.
5.Extreme caution is necessary when any Heater is used by or near children or invalids and whenever the Heater is left operating unattended.
6.This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG HEATER BE- FORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE HEATER IS ON OR PLUGGED IN.
7. | Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any man- |
| ner. There are no user serviceable parts. Please contact Customer Service at |
| EST for assistance. |
8. | To disconnect Heater, turn the Heater OFF then remove the plug from the outlet. |
9. | Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater. |
10. | Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, |
| or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation. |
11. | To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where open- |
| ings may become blocked. |
12. | Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the |
| Power Cord so the Heater or other objects are not resting on it. Do not run Power Cord under carpeting. Do not cover Power |
| Cord with throw rugs, runners, or the like. Arrange Power Cord away from room traffic and where it will not be tripped over. |
13. | This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. |
| Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of |
| the Heater and keep them at least 1 foot (0.3 m) from the sides and rear. |
14. | A Heater has hot and arcing or sparking parts inside. Do not use the Heater in areas where gasoline, paint, or flammable liquids |
| are used or stored. DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres. This |
FUNCIONAMIENTO (Figura 1)
1.Cuidadosamente retire el Calefactor de la bolsa y de la caja.
2.Coloque el Calefactor sobre una superficie firme y plana. ADVERTENCIA: Los tacos de plástico o hule, tales como las patas de esta unidad, pueden pegarse a la superficie de los muebles y/o a los pisos de madera. La unidad podría dejar un residuo capaz de oscurecer, manchar o dejar marcas permanentes en el acabado de ciertas superficies de muebles, incluyendo superficies de madera y/o pisos de madera.
3.Asegúrese que la unidad esté en la posición APAGADO (0) antes de conectar el Calefactor al tomacorriente.
4.Conecte el cable a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos dentro de los tomacorrientes, podrían deslizarse parcial o completamente fuera del tomacorriente con el menor movimiento del cable adosado. Los tomacorrientes en este estado podrían sobrecalentarse y representar un peligro de incendio grave; si queda cubierto por una cortina o tela, el peligro de incendio es todavía mayor.
5.Cuando el Calefactor se conecte por primera vez, se oirá un “bip” y la Luz de Encendido se encenderá indicando que hay electricidad en la unidad. La Luz de Encendido permanecerá encendida hasta que el Calefactor sea desconectado del tomacorriente eléctrico.
6.Gire la Perilla de Encendido hasta la posición deseada
(
) para Sólo Ventilador (SIN CALOR)
(1)para Calor Bajo
(2)para Calor Alto (1500 Watts)
7.Para el funcionamiento del Calefactor, gire la Perilla del Termostato a la posición más alta (
).
8.Para APAGAR el Calefactor, gire la Perilla de Encendido a (0) y desconecte el Calefactor del tomacorriente eléctrico.
INSTRUCCIONES DEL TERMOSTATO
1.Permita que el Calefactor caliente la habitación antes de fijar el termostato.
2.Para ajustar el termostato, gire la Perilla del Termostato hacia la (
) para aumentar la temperatura deseada o hacia la (
) para reducir la temperatura deseada.
3.Cuando se alcance la temperatura deseada, baje el termostato hasta que la Unidad se apague. Esto se hace girando la Perilla del Termostato hacia la (
).
4.El Calefactor ahora mantendrá automáticamente la temperatura seleccionada alternando la unidad entre las posiciones de encendido y apagado. Para evitar que el Calefactor alterne entre estas posiciones, ajuste el termostato.
ELEMENTOS DE SEGURIDAD
1.Hay un protector de sobrecarga térmica incorporado para evitar el sobrecalentamiento.
2.Si se alcanza una temperatura de sobrecalentamiento, el Calefactor se apagará automáticamente. Sólo podrá retomar el funcionamiento cuando el usuario reinicie la unidad.
Para Reiniciar el Calefactor:
1.Desconecte el Calefactor y espere 10 minutos hasta que la Unidad se enfríe.
2.Después que el Calefactor se haya enfriado, conecte la unidad a un tomacorriente eléctrico de 120V~ y siga las instrucciones de funcionamiento descriptas en este manual.
CONSEJOS DE SOLUCIÓN DE PROBLEMAS
Si su calefactor se apaga inesperadamente o no funciona, el elemento de seguridad arriba mencionado podría haber sido activado para evitar el sobrecalentamiento.
1.Asegúrese que el cable eléctrico esté conectado a un tomacorriente eléctrico en funcionamiento.
2.Verifique la posición de su Termostato. El Calefactor puede haberse apagado por haber alcanzado la posición de temperatura deseada.
Si usted tiene un problema que no pueda ser resuelto siguiendo los pasos enumerados arriba, comuníquese con Asistencia Técnica al
| Heater is intended for general use ONLY. |
15. | This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and |
| similar indoor locations. Never locate a Heater where it may fall into a bathtub or other water container. |
16. | Do not use Heater outdoors. |
17. Keep Heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Heater. | |
18. | This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. |
| Please refer to National Electric Code (NEC) Article |
| requirements for Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE |
19. | This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state |
| or local codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET |
| THE REQUIREMENTS OF NEC ARTICLE 500 (2008). |
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.
SAVE THESE INSTRUCTIONS
Rev. A 3/09 | 2 | 754200ES |
Perilla de | Perilla de |
Encendido | Termostato |
| Luz de |
Figura 1 | Encendido |
Rev. A 3/09 | 7 | 754200ES |
