BOTTOM RETURN FILTER INSTALLATION

REAR FILTER CLIP

 

FURNACE

 

BACK

SIDE FILTER CLIPS (2)

 

RETURN AIR OPENING

FURNACE

FURNACE

FRONT

BASE BOTTOM

 

Figure 4

4 - Clean filter with cold water and a mild soap. Direct water through filter in the opposite direction of air flow. Remove all soap residue.

5 - Allow filter to dry then spray with filter handicoater prior to reinstallation. Filter handicoater is available from your Lennox dealer as P-8-5069.

6 - Place filter in bottom of blower compartment beneath rear filter clip. Press down on filter sides. Filter clips flex, allowing filter to snap into place.

7 - Replace blower access panel.

WARNING

Blower door must be securely in place when blower and burners are operating. Gas fumes, which could contain carbon monoxide, can be drawn into living space resulting in personal injury or death.

Side Return Air Filter Installation (Figure 5)

1 - Turn off electric power to furnace.

2 - Locate the filter door of the filter rack assembly.

3 - Using the filter door pins, pull filter door, with filter at2 tached, out of filter rack assembly. Remove filter door from filter by pulling up on securing tabs.

4 - Clean filter with cold water and a mild soap. Direct water through filter in the opposite direction of air flow. Allow filter to dry, then spray with filter handi2 coater prior to reinstallation. Filter handicoater is available from your Lennox dealer as P-8-5069.

5 - Position filter door on end of filter so that the thumb tab side of the filter door is away from the furnace. Check for correct air flow position. Squeeze thumb tabs to secure filter to door.

6 - Guide filter and filter door into the filter rack installed on side of furnace. Push door into filter rack until secure.

REMOVING / REPLACING FILTER DOOR

FILTER DOOR

TAB

PIN

 

FILTER DOOR

FILTER

 

FILTER DOOR

PIN

TAB

Figure 5

Seasonal Inspections

A qualified service technician should inspect the com2 plete system each season (heating and cooling). The fol2 lowing maintenance procedures should be conducted by a qualified service technician. Do not attempt to service the unit in any way.

During a seasonal check the service technician will in2 spect the indoor blower, the burner flame and the venting system.

Venting System

Annually (before heating season) inspect furnace vent2 ing system, heat exchanger and burners for corrosion, deterioration, or deposits of debris. Remove any ob2 structions.

Inspect furnace venting system to make sure it is in place, physically sound, and without holes, corrosion, or block2 age. Vent connector must be in correct position, sloped upward and be physically sound without holes or exces2 sive corrosion.

Inspect furnace return air duct connection to ensure duct is sealed to the furnace and terminates outside the space containing the furnace.

Inspect the physical support of the furnace to guarantee that it is sound without sagging, cracks or gaps around base and it maintains seal between base and support.

Inspect and clean the condensate traps and drain.

Blower

Check and clean blower wheel for any debris. Blower mo2 tor is pre2lubricated for extended bearing life. No further lubrication is needed.

Page 5

Page 4 Page 6
Page 5
Image 5
Lennox International Inc G32V SERIES manual Seasonal Inspections, Bottom Return Filter Installation
Page 4 Page 6

G32V SERIES specifications

Lennox International Inc. is renowned for its cutting-edge HVAC solutions, and the G32V Series stands out as a prime example of their commitment to efficiency, innovation, and comfort. This series of gas furnaces is designed to meet the needs of homeowners looking for a powerful, reliable heating system without compromising on energy efficiency or environmental impact.

One of the main features of the G32V Series is its variable-speed technology. This advanced system allows for precise temperature control and quieter operation. The variable-speed blower motor adjusts the airflow based on the demand for heating, which means less energy consumption during milder weather. This feature not only enhances comfort but also significantly reduces energy bills compared to conventional systems.

Another notable characteristic of the G32V Series is its impressive Annual Fuel Utilization Efficiency (AFUE) rating of up to 96%. This level of efficiency means that a greater percentage of the energy consumed goes towards heating the home rather than being wasted through venting. As a result, homeowners can enjoy substantial savings on their utility costs while also contributing to reduced greenhouse gas emissions.

The G32V Series also incorporates a reliable and durable design, featuring a stainless steel heat exchanger that ensures excellent heat transfer and longevity. The multi-position design allows for flexible installation options, making it suitable for various home layouts. Moreover, the furnace is equipped with advanced safety features, including an integrated control board that continuously monitors the system’s operation for any abnormalities, ensuring reliable performance.

In addition, the G32V Series is compatible with a range of smart home technologies. This allows homeowners to integrate their heating system with home automation systems, enabling remote control and monitoring capabilities. The system can be integrated with Lennox’s iComfort Wi-Fi thermostat, offering homeowners the ability to adjust settings from anywhere, enhancing convenience and energy savings.

Overall, Lennox International Inc.'s G32V Series gas furnaces are designed with state-of-the-art technology and features that prioritize efficiency, comfort, and reliability. With variable-speed operation, high AFUE ratings, and compatibility with smart home technologies, these furnaces represent a significant investment in reliable home heating for the modern homeowner.
Top Page Image Contents