NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
26
GAS CONVERSION KITS
In Canada:
THE CONVERSION SHALL BE CAR-
RIED OUT IN ACCORDANCE WITH THE
REQUIREMENTS OF THE PROVINCIAL
AUTHORITIES HAVING JURISDICTION
AND IN ACCORDANCE WITH THE RE-
QUIREMENTS OF THE CAN/CSA-B149.1
INSTALLATION CODE.
LA CONVERSION DEVRA ÊTRE EF-
FECTUÉE CONFORMÉMENT AUX RE-
COMMANDATIONS DES AUTORITÉS
PROVINCIALES AYANT JURIDICTION
ET CONFORMÉMENT AUX EXIGENCES
DU CODE D'INSTALLATION CAN/CSA-
B149.1.
Gas conversion kits are available to adapt your
appliance from the use of one type of gas to
the use of another. These kits contain all the
necessary components needed to complete
the task including labeling that must be af-
fixed to ensure safe operation.
Kit part numbers are listed here and the
following steps detail the conversion pro-
cedure. Refer to the instructions provided
with the conversion kit when performing any
gas conversion.
Millivolt SIT Systems
Propane to Natural Gas
Conversion Kits
Models Cat. No.
MPB-3328 19M43
MPB-3530 H2012
MPB-4035 H2014
MPB-4540 H2016
Millivolt SIT Systems
Natural Gas To Propane Gas
Conversion Kits
Models Cat. No.
MPB-3328 H2009
MPB-3530 H2011
MPB-4035 H2013
MPB-4540 H2015
Electronic HONEYWELL Systems
Natural Gas To Propane Gas
Conversion Kits
Models Cat. No.
MPB-3328 26M59
MPB-3530 26M60
MPB-4035 26M61
MPB-4540 26M62
Electronic HONEYWELL Systems
Propane Gas To Natural Gas
Conversion Kits
Models Cat. No.
MPB-3328 19M45
MPB-3530 26M64
MPB-4035 26M65
MPB-4540 26M66
WARNING
This conversion kit shall be installed by a qualified service agency in accor-
dance with the manufacturer’s instructions and all applicable codes and
requirements of the authority having jurisdiction. If the information in these
instruction is not followed exactly, a fire, explosion or production of carbon
monoxide may result causing property damage, personal injury or loss of
life. The qualified service agency is responsible for the proper installation
of this kit. The installation is not proper and complete until the operation
of the converted appliance is checked as specified in the manufacturer’s
instructions supplied with the kit.The qualified service agency performing
this installation assumes responsibility for this conversion.
AVERTISSEMENT
Cette trousse de conversion doit être installée par un technicien agréé,
selon les instructions du fabricant et selon toutes les exigences et tous les
codes pertinents de l’autorité compétente. Assurez-vous de bien suivre
les instructions dans cette notice pour réduire au minimum le risque
d’incendie, d’explosion ou la production de monoxyde de carbone pouvant
causer des dommages matériels, des blessures ou la mort. Le tecnicien
agréé est responsable de l’installation de cette trousse. L’installation n’est
pas adéquate ni complète tant que le bon fonctionnement de l’appareil
converti n’a pas été vérifié selon les instructions du fabricant fournies avec
la trousse. Le fournisseur de service qualifié ayant réalisé l'installation
assume les responsabilités liées à la conversion.
INSTALLATION INSTRUCTIONS
Step 1. TURN OFF THE GAS SUPPLY TO THE
APPLIANCE and disconnect power supply at the
circuit breaker. Ensure appliance is cold.
CAUTION: THE GAS SUPPLY SHALL BE
SHUT OFF PRIOR TO DISCONNECTING THE
ELECTRICAL POWER, BEFORE PROCEEDING
WITH THE CONVERSION.
ATTENTION. AVANT D’EFFECTUER
LA CONVERSION, COUPEZ D’ABORD
L’ALIMENTATION EN GAZ, ENSUITE, COU-
PEZ L’ALIMENTATION ÉLECTRIQUE.
Step 2. Remove the front glass door/frame. See
Figure 21. Access the control compartment.
See Figure 19.
Step 3. Carefully remove the logs. Exercise
care so as not to break the logs.
Step 4.
Remove the burner assembly with attached
venturi tube.
Step 5. Locate the screws securing the burner
assembly to the appliance. Remove the burner
assembly and retain the securing screws.
Step 6. Millivolt Appliances - SIT Systems
a. Refer to Figure 39 and the instructions
provided with the kit. Using a Torx T20 (with
1/4" shank and center hole), remove and discard
the three pressure regulator mounting screws.
Remove the pressure regulator, spring, poppet,
diaphragm and bushing. Discard all removed
components.
Ensure the rubber gasket installed on the back of
the replacement pressure regulator is properly
positioned, and install the new pressure regula-
tor using the new screws supplied with the kit.
Tighten screws to 25 In. lb. torque.