Leviton RZCZ1 installation instructions Introduction, Features

DI-000-RZCZ4-00A-X1

WARNINGS AND CAUTIONS:

•ON/OFF LED for remote load control.

•To be installed and/or used in accordance with appropriate electrical codes and regulations.

•If you are unsure about any part of these instructions, consult a qualified electrician.

•Vizia™ RF RZCZ4 remote does not control the load, but provides scene applications to operate with ViziaTM RF switches.

•Recommended minimum wall box depth is 2-1/2".

4-Zone Controller

Cat. No. RZCZ4	Compatible with	TMenabled products!
120VAC, 60Hz
Installation Instructions

WARNINGS AND CAUTIONS:

•Can call up four (4) zone ON/OFF with advanced Programmer/Remote (see RZCPG).

•Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.

•Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

INTRODUCTION

Leviton’s ViziaTM RF components are designed to communicate with each other via Radio Frequency (RF) to provide remote control of your lighting. Using RF technology allows Leviton to provide the greatest signal integrity possible. Each module in Leviton’s ViziaTM RF component line is a Z-WaveTMenabled device. In a Z-WaveTMnetwork, each device is designed to act as a router. These routers will re-transmit the RF signal from one device to another until the intended device is reached. This ensures that the signal is received by its intended device by routing the signal around obstacles and radio dead spots. The 4-Zone Controller

is compatible with any Z-Wave™ enabled network, regardless of the manufacturer and can also be used with other devices displaying the Z-Wave™ logo.

FEATURES

•This is a Z-Wave™ Controller

•Zone/Area control without traveler wires

•Can control ON/OFF dim/bright for up to 4 Zones/Area.

•ON/OFF LED

•Two way communication

•RF reliability

•Ease of installation – No new wiring

•Compatible with other Z-Wave™ enabled devices

INSTALLING YOUR 4-ZONE CONTROLLER

NOTE: Use check boxes when Steps are completed.

	WARNING: TO AVOID FIRE, SHOCK OR DEATH; TURN
Step 1
	OFF POWER at circuit breaker or fuse and test that power is off
	before wiring!

/&& /./&& /. /&& /./&& /. /&& /./&& /. /&& /./&& /.

/&&	/.	/&&	/.
/&&	/.	/&&	/.

Step 2 Identifying your wiring application (most common):

NOTE: If the wiring in your wall box does not resemble this configuration, consult a qualified electrician.

	1.	Line (Hot)
	2.	Neutral
	3.	Ground
1	2
3

Step 4 Wiring Application:

4-Zone Controlller

WH BK Hot (Black)

Green

Ground

Line

120VAC, 60Hz

Neutral (White)

WIRING SWITCH:

Connect wires per WIRING DIAGRAM as follows:

•Green or bare copper wire in wall box to Green terminal screw.

•Line Hot wall box wire to terminal screw marked "BK".

•Line Neutral wall box wire to terminal screw marked "WH".

	Testing your 4-Zone Controller prior to mounting
Step 5
	in wall box:
	• Position all wires to provide room in
	outlet wall box for device.
	• Ensure that the word “TOP” is facing up
	on device strap.
	• Partially screw in mounting screws in
	wall box mounting holes.
	NOTE: Dress wires with a bend as

Step 6 cont'd

B)If using RZCPG Programmer/Remote, you will be prompted to place 4-Zone controller into programming mode.

C)To access Program mode, press and hold the left side of buttons 1 and 3 (refer to figure). Wait 5 seconds until the LED turns Amber. Release the button and the LED will blink

Amber. You are now in Programming mode. NOTE: If the LED on the 4-Zone controller turns solid Red while including, there has been a communication error.

D) While standing close to the 4-Zone controller (approximately 2-5 ft.), press the center button on the Programmer/Remote to <Include> device in the network. NOTE: Only one device may be included at any time.

E)	The Primary Programmer/Remote will assign
	a Home ID, Node ID, and Name for this
	device.
	NOTE: This information will be stored in the Programmer/Remote to
	be used for future reference.
	NOTE: You may name or edit the node of this device at this time.
F)	The 4-Zone controller is now installed in the network.
G)	After all devices are included into the network, the controller must
	be updated to allow proper network function. To update controller
	proceed as follows:
	• If using a non-Leviton Programmer/Remote, refer to the

Tools needed to install your 4-Zone Controller:

Slotted/Phillips Screwdriver	Electrical Tape	Pliers
Pencil	Cutters	Ruler

Changing the color of your 4-Zone Controller:

Your 4-Zone controller includes three color options. The controller ships with the White frame attached. To change color of frame, proceed as follows:

Push in	Line up tabs
side at tab	and press in
to release	side to attach

After frame is removed, remove existing push buttons by pressing out buttons from back of frame and replace them with desired color change push buttons by pressing in from front of frame. To make IR capable, use new DIM/BRIGHT button with IR window.

Step 3 Preparing and connecting wires:

This 4-Zone controller can be wired using side wire terminal screws or through backwire openings. Choose appropriate wire stripping specifications accordingly.

	5/8"	Strip Gage
	(1.6 cm)
		(measure bare
Cut
		wire here)
(if necessary)

Side Wire Connection	Back Wire (either hole may be used)
Side wire terminals accept	Back wire openings use #14-12 AWG
#14 AWG solid wire copper only.	solid wire copper only.

•Make sure that the ends of the wires from the wall box are straight (cut if necessary).

shown in diagram in order to relieve

stress when mounting device.

•Restore power at circuit breaker or fuse.

•LED should turn ON, when any button is pressed. If LED does not turn

ON, refer to the TROUBLESHOOTING section.

	Including 4-Zone Controller into Z-WaveTM
Step 6
	Network:

NOTES:

•If using a non-Leviton Programmer/Remote, refer to the Programmer/ Remote instruction sheet.

•4-Zone controllers incuded into a Z-WaveTMnetwork must be updated after you have included all other devices.

A)If using a Leviton Z-WaveTMProgrammer/Remote, Cat. No. RZCPG, press the Menu button and scroll down to System Setup. Press the center button to select System Setup Menu. Press the center button to select Network. Press the center button to <Include Node>.

Programmer/Remote instruction sheet for updating controller.

• If using Leviton Z-WaveTMProgrammer/Remote, Cat. No. RZCPG,

press the Menu button and scroll down to System Setup. Press

the center button to select System Setup Menu. Press the center

button to select Network. Press the center button to select Update

"cntrl". When prompted, press desired button on 4-Zone controller.

• Wait until the RZCPG Programmer/Remote confirms completion.

Update is done.

Note: If the 4-Zone controller has been
successfully Included in the network and
the user tries to Include it again without first
excluding it from the network, the controller
will retain the first node ID it had received and
ignore the second.		Menu
		Button
Center	1 ON	OFF
Button
	2 ON	OFF
	3 ON	OFF
Programmer/Remote	4 ON	OFF
Cat. No. RZCPG