Manual Pro:Centric Configuration
1.With the Searching for Pro:Centric Server screen on display, use the arrow keys on the Installer Remote to select/highlight the Manual Pro:Centric option at the bottom right of the screen, and press OK.
In the Pro:Centric Manual Configuration screen (see examples at right below), you will be able to configure the appropriate Pro:Centric settings in the TV. Use the Up/Down arrow keys on the Installer Remote to navigate between fields.
2.In the Pro:Centric Mode field, use the Left/Right arrow keys to select the appropriate Pro:Centric Application Mode— GEM, FLASH, HTML, or Configuration Only.
Note: For remote management only, select “Configuration Only.” The TV will search for TV
3.Refer to the appropriate subsection below, depending on the Pro:Centric server configuration, to complete the remaining fields.
RF Configuration
a)In the Media Type field, use the Left/Right arrow keys to select RF.
b)In the Data Channel field, either key in or use the Left/ Right arrow keys to select the RF channel number that will be used by the Pro:Centric server as its data channel. The Data Channel value can be set from 1 to 135. *
IP Configuration
a)In the Media Type field, use the Left/Right arrow keys to select IP.
Note: By default, the Pro:Centric Manual Configuration screen initially shows RF configuration fields. When you select “IP” as the Media Type, the Data Channel and Signal Strength fields are replaced with (IP) Address and Port fields.
b)In the Address and Port fields, either key in or use the Left/Right arrow keys to select the appropriate values for the Pro:Centric server IP address and port number.
The IP address must match the IPv4 multicast address and the port number must match the port number that is set in the Pro:Centric server.
1 2 3 4
Searching for Pro:Centric Server...
It may take 1 min 32 second(s).
This step automatically searches for the Pro:Centric server.
If there is no Pro:Centric Server installed, you do not need to continue with this procedure. Please select either ‘Exit’ or ‘Manual Pro:Centric’.
Status : Tuning channel 49
TV is now searching all of the channels for the data channel...
Back |
| Exit |
| Manual Pro:Centric |
1 2 3 4
Pro:Centric Manual Configuration
Pro:Centric Mode | < | GEM | > |
| |||||
Media Type |
|
| RF |
|
|
|
| ||
Data Channel |
|
|
|
|
|
| |||
| 1 |
|
|
|
| ||||
Signal Strength |
|
|
|
|
| 0% | |||
|
|
|
|
| |||||
Signal Quality |
|
|
|
| 0% | ||||
| No signal |
| |||||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
Back |
|
| Exit |
|
| Next | |||
Pro:Centric Manual Configuration Screen with
RF Media Fields
1 2 3 4
Pro:Centric Manual Configuration
Pro:Centric Mode |
| GEM |
|
| ||||||
Media Type | < |
| IP | > |
| |||||
Addresss |
| 255 | 255 |
| 255 | 255 |
| |||
|
|
|
|
|
|
|
|
|
|
|
Port |
|
| 0 |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
Back |
|
|
| Exit |
|
|
|
| Next | |
|
|
|
|
|
|
|
|
|
|
|
Pro:Centric Manual Configuration Screen with
IP Media Fields
(Continued on next page)
*PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.
17 |