LG Electronics 42LQ640H Preventing Image burn or Burn-in on your TV, Screen, YyGenerated Sound

		IMPORTANT SAFETY INSTRUCTIONS	5
yyDot Defect	For USA and Canada
The Plasma or LCD panel is a high technology
product with resolution of two million to six million
pixels. In a very few cases, you could see fine dots
		FCC NOTICE
on the screen while you’re viewing the TV. Those
dots are deactivated pixels and do not affect the	This equipment has been tested and found to
performance and reliability of the TV.
	comply with the limits for a Class B digital device,
yyGenerated Sound
	pursuant to Part 15 of the FCC Rules. These limits
“Cracking” noise: A cracking noise that occurs
	are designed to provide reasonable protection
when watching or turning off the TV is generated by
	against harmful interference in a residential
plastic thermal contraction due to temperature and
	installation. This equipment generates, uses and can
humidity. This noise is common for products where
	radiate radio frequency energy and, if not installed
thermal deformation is required.
	and used in accordance with the instructions, may
Electrical circuit humming/panel buzzing: A low level
	cause harmful interference to radio communications.
noise is generated from a high-speed switching
	However, there is no guarantee that interference
circuit, which supplies a large amount of current
	will not occur in a particular installation. If this
to operate a product. It varies depending on the
	equipment does cause harmful interference to radio
product.
	or television reception, which can be determined
This generated sound does not affect the
	by turning the equipment off and on, the user is
performance and reliability of the product.
	encouraged to try to correct the interference by one
yyTake care not to touch the ventilation openings.
	or more of the following measures:
When watching the TV for a long period, the
		- Reorient or relocate the receiving antenna.
ventilation openings may become hot. This does
not affect the performance of the product or cause		- Increase the separation between the
defects in the product.		equipment and the receiver.
yyIf the TV feels cold to the touch, there may be a		- Connect the equipment to an outlet on a circuit
small “flicker” when it is turned on. This is normal,		different from that to which the receiver is
there is nothing wrong with TV. Some minute dot		connected.
defects may be visible on the screen, appearing as		- Consult the dealer or an experienced radio/TV
tiny red, green, or blue spots. However, they have		technician for help.
no adverse effect on the TV’s performance. Avoid	This device complies with part 15 of the FCC Rules.
touching the LCD screen or holding your finger(s)	Operation is subject to the following two conditions:
against it for long periods of time. Doing so may	(1) this device may not cause harmful interference
produce some temporary distortion effects on the	and (2) this device must accept any interference
screen.	received, including interference that may cause

		undesired operation of the device.
	Preventing “Image burn” or “Burn-in” on your TV	Any changes or modifications in construction of
		this device which are not expressly approved by
screen
		the party responsible for compliance could void the
		user’s authority to operate the equipment.
			NOTE TO CABLE/TV INSTALLER

ENGLISH

yyIf a fixed image displays on the TV screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is “image burn” or “burn-in” and not covered by the warranty.

yyIf the aspect ratio of the TV is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the screen.

yyAvoid displaying a fixed image on the TV screen for a long period of time (2 or more hours for LCD, 1 or more hours for the Plasma TV) to prevent image burn.

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.