25.0 LIGHTING INSTRUCTIONS & TURNING OFF APPLIANCE

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY

RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

 

A.

This appliance has a pilot which must be lit with a piezo

 

• Immediately call your gas supplier from a neighbor’s phone.

 

 

 

spark igniter. When lighting the pilot, follow these instructions

 

Follow the gas supplier’s instructions.

 

 

 

 

exactly.

 

 

• If you cannot reach your gas supplier, call the fire department.

 

 

B.

 

 

 

 

 

 

BEFORE OPERATING smell all around the heater area for gas.

C.

Use only your hand to push in or turn the gas control knob.

 

 

 

Be sure to smell next to the floor because some gas is heavier

 

 

 

than air and will settle on the floor.

 

 

Never use tools. If the knob will not push in or turn by hand, do

 

 

 

 

 

 

 

not try to repair it, call a qualified service technician. Forced or

 

 

WHAT TO DO IF YOU SMELL GAS

 

 

attempted repair may result in a fire or explosion.

 

 

 

• Do not try to light any appliance.

 

D.

Do not use this heater if any part has been under water.

 

 

 

 

 

 

 

Immediately call a qualified service technician to inspect the

 

 

 

• Do not touch any electric switch; do not use any phone in your

 

appliance and to replace any part of the control system and any

 

 

 

building.

 

 

gas control which has been under water.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LIGHTING INSTRUCTIONS

 

 

 

 

 

1. Stop! Read the safety information above.

 

7. Continue turning counter-clockwise

through the spark click

 

 

 

 

 

 

to the PILOT light position, ensuring the pilot has lit. If not, turn the knob

 

 

2. Make sure manual shut-off valve is fully open.

 

fully clockwise,

and repeat.

 

 

 

3. Depress control knob in and turn clockwise

to the

8. Hold the control knob in for a further 10 seconds to prevent the flame

 

 

“OFF” position (Figure 13).

 

failure detector from shutting off the gas while the probe is warming up.

 

 

4. Wait 5 minutes to clear out any gas. Then smell for gas, including near

9. Release the control knob while turning counter-clockwise

 

 

the floor. If you smell gas, STOP! Follow the safety instructions in “What

to the preferred setting. Close the control access panel.

 

 

to do if you smell gas” under section ‘B’ above. If you do not smell gas, go

 

 

 

 

 

 

 

to next step.

 

• If the knob does not pop out when released, stop and immediately call

 

 

 

 

 

 

your service technician or gas supplier.

 

 

5. The pilot is located on the left side behind the burner (Figure 13).

 

 

• If the pilot will not stay lit after several tries, depress and turn the gas

6. Depress control knob in and turn counter-clockwise

to the

control knob clockwise

to “OFF” and wait 30 seconds.

“SPARK” position (Figure 13) and hold there for a few seconds.

 

Depress and turn knob counter-clockwise

to “SPARK”

 

 

and ignite the heater again. If your pilot does not relight depress and

Note: If you are running the heater for the first time or after an extended

turn control knob clockwise

 

to “OFF” and call your service

period of non use it will be necessary to press the control knob all the way

technician or gas supplier.

 

 

in for 30 seconds to allow air to bleed out of the gas piping.

 

 

 

 

 

 

10. Wait 30 seconds before readjusting the heater when the control knob

 

 

has been turned down to a lower setting.

 

 

 

 

 

 

 

TO TURN OFF GAS TO APPLIANCE

 

 

 

 

1. Depress and turn control knob clockwise

to the “OFF”

 

 

 

position (Figure 13).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 13

 

 

 

The control knob is located on the lower

 

 

 

 

 

 

 

 

 

Figure 14

 

 

‘OFF’ position

 

 

 

 

 

 

 

 

 

right hand side of the outer case. It is of a

 

 

 

 

 

 

 

spherical design and is marked as shown

 

 

 

 

 

‘SPARK’ position

 

 

 

in Figure 13.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

‘LOW’ position

 

 

Figure 14: Pilot assembly. This is located

 

 

 

 

 

 

 

 

behind the burner, on the left-hand side of

 

 

 

 

 

 

the appliance.

 

 

 

 

 

‘HIGH’ position

 

 

 

 

 

 

 

 

 

13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE