ADJUSTMENT
All adjustment are thoroughly checked and corrected 2. | Adjustment for White Balance | |||
when the monitor leaves the factory, but sometimes |
| 1) | Display Black pattern at SXGA/60Hz. | |
several minor adjustment may be required. |
| 2) | Set External Bright to MAX position and Contrast to | |
Adjustment should be following procedure and after |
|
| 80 Position. | |
warming up for a minimum of 10 minutes. |
| 3) | Select PRESET START → BIAS CAL command | |
• Alignment appliances and tools. |
|
| and Enter. | |
| 4) | No attempt to manually adjust, BIAS data is auto- | ||
- IBM compatible PC |
| |||
|
| matically adjusted and saved to the EEPROM. | ||
- Programmable Signal Generator. |
|
| ||
| 5) | Display Full White pattern at SXGA/60Hz. | ||
(eg. |
| |||
| 6) | Select DRIVE CAL command and Enter. | ||
- E(E)PROM with each mode data saved. |
| |||
| 7) | 9300K are automatically adjusted and | ||
|
| |||
1. Adjustment Start |
|
| saved to the EEPROM. | |
| 8) | Select PRESET EXIT command and Enter. | ||
1) Display any pattern at any Mode. |
| |||
|
|
| ||
2) Run alignment program for LB782G on the IBM | 3. | Adjustment for EDID | ||
compatible PC. | ||||
| 1) | Use this procedure only when there is some | ||
3) Select EEPROM → ALL INIT command and Enter. |
| |||
|
| probelm on EDID data. | ||
4) This will make all data to default state. |
|
| ||
| 2) | Connect the | ||
5) Select COMMAND → PRESET START command |
| |||
| 3) Select EEPROM → EDID(A) WR command and | |||
and Enter. |
| |||
|
| Enter. | ||
|
|
| ||
|
|
|
|
|
|
|
|
|
| A |
|
|
|
|
|
|
|
|
|
|
|
|
| 9 | 6 |
|
|
|
|
|
|
|
|
|
| IBM | 15 | 5 | 1 |
|
|
Video Signal |
|
|
|
|
|
|
| Compatible PC | 11 |
|
|
| |
|
|
|
|
|
|
| 10 | 6 |
|
|
| ||
Generator |
|
|
|
|
|
|
|
| 5 | 1 |
|
| C |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| used |
|
|
| PARALLEL PORT |
|
| 13 |
| 1 |
|
|
| Not |
|
|
|
|
|
| 25 |
| 14 | |
|
|
| RS232C |
|
| OFF | ON |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
| 5V |
|
|
|
|
| |
|
|
|
|
|
|
| F |
|
|
|
|
| |
Line |
|
| PARALLEL |
|
|
|
|
|
|
|
| ||
C |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |||
Control |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| 5V | |
|
|
|
|
|
|
| Power inlet (required) |
|
|
|
| 4.7K | |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| 220 |
| ON |
| 5V | 4.7K | |
|
|
|
|
|
|
| POWER | Power Select Switch |
|
| E |
| |
|
|
|
| VGS |
|
|
|
|
| ||||
|
|
|
|
| (110V/220V) |
| OFF |
| 74LS06 | ||||
|
| A |
|
| MONITOR |
| ST | Power LED |
|
|
| 4.7K | |
|
|
|
| V - SYNC |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 74LS06 |
| ||
|
|
|
|
| B |
|
| E ST Switch |
| B |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| F |
|
|
|
|
| |
|
|
|
|
|
|
|
| (Switch must be ON.) |
|
|
|
|
|
Figure 1. Cable Connection
- 11 -
