Mechanical Installation

Mounting Methods

General Information

•Select the appropriate orientation to maximize sunlight exposure.

•Module should not be mounted or stored in a way that the front/top glass faces downward in order to prevent water from entering the junction box, which could cause a safety hazard.

•Clearance between the solar module frames and structures such as roofs or ground is required to prevent wiring damage and to allow air to circulate behind the solar module. The recommended standoff height is a minimum of 100mm

•When installed on a roof, the solar module must be mounted over a fire-resistant roof covering rated for the application. The fire resistance of the solar module is class C after ANSI/UL790.

•The solar module is only IEC listed for use when its factory frame is fully intact.

•Removal or alteration must be done by an authorized and qualified individual

•Creating additional mounting holes may damage the solar module and reduce the strength of the frame.

•We recommend a 6mm gap between module frames to avoid tension from thermal expansion.

•The fire rating of this module is valid only when mounted in the manner specified in the mechanical mounting instructions.

•The module is considered to be in compliance with UL1703 only when the module in mounted in the manner specified by the mounting instructions below.

•The solar module may be mounted by using the following methods: (*Torque:8~12Nm )

•When installing modules in heavy snow areas, it is recommended to be taken an appropriate countermeasure to prevent possible damages to the lower side frame by slipping snow .

(e.g. attach supporting part to the lowest modules)

Solar module

Supporting part

Roof

Mounting by using frame bolts holes

•Secure the solar module to the structure by using the factory mounting holes.

•Four M6 stainless steel bolts, four nuts, four spring washers, and eight flat washers are recommended per solar module.

•The module may be fastened to a support by using both the outer and inner bolt holes of the frame.

•Each module should be securely fastened at a minimum 4 points on two opposite sides.

•Specific information on the solar module dimensions and location of mounting holes is provided in ‘Product Specifications’.

Module frame

Bolt

Flat washer

Flat washer

Spring washer

Nut

Support

•Tighten the bolt securely by using the combination shown above. Place the spring washer between the Flat washer and Nut.

Mounting by using clamps

•The module may be fastened to a support by using clamps on both the long edge and the short edge of the modules.

•Specific information on the solar module dimensions and location of clamping is provided in ‘Product Specifications’.

6

Page 6 Page 8
Page 7
Image 7
LG Electronics LGXXXN1C(W)-G3 installation instructions Mounting Methods, General Information
Page 6 Page 8

LGXXXN1C(W)-G3 specifications

LG Electronics continues to lead the way in innovative home appliance solutions with its latest model, the LGXXXN1C(W)-G3 air conditioner. This system has been engineered to provide superior performance, energy efficiency, and user convenience, making it a popular choice for homeowners looking to enhance their indoor comfort.

One of the standout features of the LGXXXN1C(W)-G3 is its advanced inverter technology, which allows for precise temperature control. Unlike conventional air conditioning units that cycle on and off, the inverter compressor adjusts its speed dynamically to maintain the desired climate, resulting in reduced energy consumption and lower utility bills. This energy-efficient operation significantly minimizes environmental impact while maximizing comfort.

The LGXXXN1C(W)-G3 boasts a sleek and modern design that seamlessly blends with a variety of interior decors. It is equipped with a user-friendly LED display and intuitive controls that make it easy to set and adjust the desired temperature and mode of operation. Additionally, the unit features a remote control option, allowing users to adjust settings from anywhere in the room.

Another remarkable characteristic of this model is its powerful air filtration system. The LGXXXN1C(W)-G3 is designed with a multi-stage filtration process that effectively captures dust, allergens, and other airborne particles. This not only improves the air quality in the home but also aids in the overall health and well-being of the occupants.

To ensure optimum comfort, the LGXXXN1C(W)-G3 is equipped with a turbo cooling function, allowing it to rapidly reach the desired temperature on hot summer days. This quick-response capability means users can enjoy a cooled environment in a matter of minutes.

The unit is designed with whisper-quiet operation in mind, making it a perfect choice for bedrooms and other quiet spaces. This low noise level is achieved through smart engineering, allowing for a tranquil living atmosphere without disturbing everyday activities.

Additionally, the LGXXXN1C(W)-G3 is compatible with smart home ecosystems, enabling users to control their air conditioning system remotely via smartphone apps or voice commands. This flexibility aligns with modern lifestyle trends, offering convenience and ease of use.

In summary, the LG Electronics LGXXXN1C(W)-G3 air conditioner stands out for its energy efficiency, advanced inverter technology, effective air filtration, rapid cooling capabilities, quiet operation, and smart control features. These combined elements make it an ideal choice for consumers seeking comfort, convenience, and environmental responsibility in their climate control solutions.
Top Page Image Contents