LG Electronics LG DVD Receiver Hdmi Connection, Resolution setting, About Hdmi, Not supplied

HDMI Connection

About HDMI

HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for an easy all- digital output to an HDMI or DI-equipped TV.

Connection to an HDMI TV requires an HDMI cable while connection to a DVI-equipped TV requires a DVI adapter besides a HDMI cable.

HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multi-channel surround-sound audio, HDMI features include uncompressed digital video, a bandwidth of up to 5 gigabytes per second, one connector (instead of several cables and connector), and communication between the AV source and AV devices such as DTVs.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.

If you have a HDMI TV or monitor, you can connect it to this DVD/CD Receiver using a HDMI cable.

1.Connect the HDMI OUT jack on the DVD/CD Receiver to the HDMI jack on a HDMI compatible TV or monitor (H).

2.Set the TV’s source to HDMI (refer to owner’s manual for TV).

3.In the stop mode, select HDMI mode by pressing HDMI. Press RESOL. repeatedly to select the resolution you wish to change.

Notes:

The arrow on the cable connector body should face up for correct alignment with the connector on the DVD/CD Receiver.

If HDMI cable is not connected, the HDMI button does not operate.

If there is noise or there are lines

on the screen, please check the HDMI cable.

Not all HDCP-compatible DVI devices will work with this DVD/CD Receiver.

If TV does not support HDCP, snow noise appears on the screen, or picture may be vibrated.

Tip :

When you use HDMI connection, you can change the resolution (480p, 720p, 1080i) for the HDMI output by pressing RESOL. on the Remote Control.

Important Note

If you turn off the TV or disconnect the HDMI cable during playback of the device, playback will pause.

You have to click on the play button to play back again.

For some TVs, when you change the TV mode, such condition specified above may happen.

Rear of DVD/CD Receiver

MONITOR		INPUT
		L - AUX - R
			HDMI OUT
Y	PB	PR	XM IN
	COMPONENT VIDEO (PROGRESSIVE SCAN)		i Pod

H (Not supplied)

HDMI compatible TV HDMI

Resolution setting

You can change the resolution for the COMPONENT VIDEO OUT by pressing RESOL. on the Remote Control. Available resolution settings are as shown below.

OUTPUT	Available Resolution
CONNECTION
HDMI	920 x 1080i
VIDEO OUT	1280 x 720p
	720 x 480p
COMPONENT	1920 x 1080i
VIDEO OUT	1280 x 720p
	720 x 480p
	720 x 480i
MONITOR OUT	720 x 480i

Notes:

If the picture does not appear on the screen with the analog video connections, change the resolution to 480i.

For 720p and 1080i resolution on the component video out, only non-copy protected discs can be played back. If the disc is copy protected, it will be displayed at the 480p resolution.

1080i, 720p, and 480p does not work with the analog video connections (MONITOR OUT).

The component (Y/PB/PR) will output to black picture in the RGB mode.

If you change the resolution, the display MENU (MP3/JPEG/DivX) size is changed.

If your TV does not accept your resolution setting, abnormal picture appears on the screen.

Please read owner’s manual for TV, and then set the resolution that your TV can accept.

Caution:

Changing the resolution when the DVD/CD Receiver is connected with HDMI connector may result in malfunctions. To solve the problem, turn off the DVD/CD Receiver and then turn it on again.

Installation and Setup

11