Life Fitness 93Xe manual 10 a

IMPORTANT! Do not discard the ship kit located on top of the pedal levers. All necessary components needed to complete the installation are located in the ship kit.

IMPORTANT! Ne jetez pas le kit placé sur le dessus des leviers de pédale. Il contient tous les éléments nécessaires pour l'installation.

1. Locate the LEFT HANDLEBAR (11). Position the HANDLEBAR near the top of

the LEFT PIVOT ARM (A). Connect the HEART RATE CONNECTOR (B)

leading from the HANDLEBAR to the CONNECTOR (C) extending from the top

of the LEFT PIVOT ARM. Carefully slide the excess HEART RATE CABLE into

the top of the LEFT PIVOT ARM.

Align the mounting holes of the LEFT HANDLEBAR with the mounting holes at

the top of the LEFT PIVOT ARM. Secure them together using three SCREWS

(1).

9

11

	NOTE: Be careful not to pinch the HEART RATE CABLE when securing the
	LEFT HANDLEBAR to the LEFT PIVOT ARM.
	REMARQUE : Faites attention de ne pas coincer le CÂBLE DU MONITEUR
	DE FRÉQUENCE CARDIAQUE en fixant le GUIDON GAUCHE au BRAS
	MOBILE GAUCHE.
2.	Locate one LEFT FRONT ROCKER COVER (5) and the LEFT BACK
	ROCKER COVER (6). Position the LEFT BACK ROCKER COVER over the
	user side of the ROCKER ARM making sure that it seats fully over the
	BULLHORN MOUNTING BRACKET (D). Place the FRONT ROCKER COVER
	over the opposite side of the ROCKER ARM in the same manner. Secure the
	COVERS using two PHILLIPS PAN HEAD SCREWS (2). Tighten the
	SCREWS securely. Do not over-tighten the SCREWS.
3.	Locate one FRONT PIVOT ARM COVER (9) and one BACK PIVOT ARM
	COVER (10). Position the BACK PIVOT ARM COVER over the user side of the
	ROCKER ARM making sure that it interlocks with the ROCKER COVER. Place
	the FRONT PIVOT ARM COVER over the opposite side of the PIVOT ARM in
	the same manner. Secure the COVERS using two PHILLIPS PAN HEAD
	SCREWS (2). Tighten the SCREWS securely. Do not over-tighten the
	SCREWS.
4.	Locate the LEFT BULLHORN (13). Secure the BULLHORN to THE
	BULLHORN MOUNTING BRACKET (D) using two FLAT HEAD SCREWS (1).
	Tighten the SCREWS securely. Locate and attach the LEFT BULLHORN
	COVER (15) to the base of the BULLHORN using one SCREW (22). Tighten
	the SCREW securely. Do not over-tighten the SCREW. Slide the GASKET (E)
	downward to meet the BULLHORN COVER.

B C

2

1

10 A

5

D

A

E

6

5.	Repeat steps one through four to install the RIGHT ROCKER COVERS (5 &
	6), PIVOT ARM COVERS (9 & 10), BULLHORN (14) and BULLHORN COVER
	(16).
	NOTE: The right PIVOT ARM COVERS are reversed front and back. The
	SCREWS will be installed from the rear.
	REMARQUE : Les couvercles du BRAS MOBILE DROIT sont inversés à
	l'avant et à l'arrière. Les VIS sont insérées de l'arrière.
6.	Unwrap the MAIN WIRE, COAXIAL CABLE and HEART RATE HARNESS
	leading from the MONOCOLUMN (F). Feed the WIRE HARNESSES through
	the CONSOLE SUPPORT ASSEMBLY TUBE (G) located at the top and front
	of the MONOCOLUMN. Locate the CONSOLE SUPPORT ASSEMBLY (7) and
	position it near the top of the MONOCOLUMN. Feed the WIRE HARNESSES
	through the CONSOLE SUPPORT ASSEMBLY as shown. Align the bottom
	mounting holes of the CONSOLE SUPPORT ASSEMBLY with those in the
	CONSOLE SUPPORT ASSEMBLY TUBE. Secure them together using six
	SCREWS (1). Tighten the SCREWS securely.
	NOTE: Be careful not to damage the WIRE HARNESSES when routing it
	through the CONSOLE SUPPORT ASSEMBLY or when mounting the
	CONSOLE SUPPORT ASSEMBLY to the CONSOLE SUPPORT ASSEMBLY
	TUBE.
	REMARQUE : Faites attention de ne pas coincer les FAISCEAUX DE
	CÂBLES en les insérant dans le SUPPORT DE LA CONSOLE ou en fixant le
	SUPPORT DE LA CONSOLE au TUBE DE SUPPORT DE LA CONSOLE.
7.	Locate the ACCESSORY TRAY (17). Slide the ACCESSORY TRAY into the
	top of the MONOCOLUMN (F) as shown. Be sure the ACCESSORY TRAY is
	fully seated.
	NOTE: Be careful not to damage the MAIN WIRE HARNESS when sliding
	the ACCESSORY TRAY into the MONOCOLUMN.
	REMARQUE : Faites attention de ne pas endommager le FAISCEAU DE
	CÂBLES PRINCIPAL en glissant le PLATEAU POUR ACCESSOIRES sur la
	COLONNE MONOBLOC.
	Secure the ACCESSORY TRAY to the CONSOLE SUPPORT ASSEMBLY
	using two SCREWS (3). Tighten the SCREWS securely. Do not over-tighten
	the SCREWS.

21 2 7

2

1

83

2 13

1

15 22

1

G

F

4

17