3.5 CONNECT WIRING / ATTACH COVER
Parts: Hardware Bag #3 | (4, 12mm Phillips Screws) |
| (4, Flat Washers) |
Tools: Phillips Screwdriver |
|
Detach the WIRE TIE (H) attached to the front of the MONOCOL-
UMN (E). Carefully pull the CONSOLE WIRE (L) through the SIDE
ACCESS HOLE (M) of the MONOCOLUMN (E). Feed the CON-
SOLE WIRE through the GROMMET (N) as shown and insert the
GROMMET into the SIDE ACCESS HOLE.
Connect the WIRE (K) leading from the MONOCOLUMN BRACKET
(J) to the corresponding CONSOLE WIRE (L) from the SIDE ACCESS HOLE (M) of the MONOCOLUMN (E). Slide the MONO- COLUMN COVER (F) downward to the meet the MAIN SHROUDS. Secure the MONOCOLUMN COVER to the MAIN SHROUDS using four 12mm PHILLIPS SCREWS (6) and matching FLAT WASHERS
(7). Tighten the SCREWS securely. Do not overtighten the
SCREWS.
3.6ASSEMBLE THE SEAT AND SEAT POST
Parts: Hardware Bag #4 | (3, Nylock Nuts) |
|
| |
| (3, Flat Washers) |
|
| |
| (2, 8mm Phillips Screws) |
|
| |
| (1, 6mm Phillips Screw with Locking Compound) |
| ||
| (2, 6mm Phillips Screws) |
|
| |
Tools: 13mm Socket Wrench, Phillips Screwdriver |
|
| ||
Locate the SEAT (O) and SEAT POST (P). Remove the three |
|
| ||
NYLOCK NUTS (8) and FLAT WASHERS (9) from the threaded |
|
| ||
studs on the bottom of the SEAT. Align the threaded studs of the | Q | O | ||
SEAT with the mounting holes in the SEAT POST MOUNTING | ||||
PLATE (Q). Secure the seat to the SEAT POST MOUNTING PLATE | 9 |
| ||
using the three previously removed NYLOCK NUTS and FLAT | P | |||
| ||||
WASHERS. Tighten the NUTS securely. | 8 | |||
| ||||
Locate the SEAT POST CAP (R). With the curved side facing | R | 10 | ||
upward toward the SEAT (O) and the inside notch aligned with the | ||||
| ||||
SEAT POST (P) adjustment decal, slide the SEAT POST CAP over | 11 |
| ||
the SEAT POST |
| T | ||
| S | |||
|
| |||
Locate and slide the SEAT POST SPACER (S) over the end of the | U | |||
12 | ||||
SEAT POST (P). Be sure the locking tabs fully engage the holes |
| |||
|
| |||
located at the bottom of the SEAT POST. Secure the SEAT POST |
|
| ||
SPACER using two 8 mm PHILLIPS SCREWS (10). |
|
| ||
With the nose of the SEAT (O) facing forward, insert the SEAT POST
(P) into the SEAT POST SUPPORT (T).
Slide the SEAT POST CAP (R) downward to meet the top of the
SEAT POST SUPPORT (T). Secure the SEAT POST CAP to the SEAT POST SUPPORT using two 6mm PHILLIPS SCREWS (11). Tighten the SCREWS securely. Do not overtighten the SCREWS.
Begin inserting the SEAT ADJUSTMENT KNOB (U). Lift upward on the SEAT (O) and SEAT POST (P) until the SEAT POST locks into a position. Tighten the SEAT ADJUSTMENT KNOB fully. Insert the 6mm PHILLIPS SCREW W/LOCK- ING COMPOUND (12) and tighten securely.
11
