![](/images/new-backgrounds/1028287/282871x1.webp)
READ AND UNDERSTAND ALL TRACK, CONNECTOR,
INSTRUCTION SHEETS BEFORE INSTALLING ANY TRACK ITEM
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal regulations. To assure full compliance with codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:26096
0597 | Page 1 of 3 |
GRID CEILING CANOPY KIT AND GRID CEILING MOUNTING CLIPS
FOR USE WITH PROSPEC® TRACK SYSTEMS ONLY
CEILING & CEILING | GRID CEILING | |||||||||||||||||||
PANEL TYPE |
|
|
|
|
|
|
|
|
|
|
| MOUNTING CLIP | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| USE |
| USE | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (ORDER SEPARATELY) | |
|
| 15/16” |
|
|
|
|
|
| 9/16” |
|
|
|
|
|
|
|
|
| 6089 |
|
|
|
|
|
|
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CANOPY SPACER CROSS BAR & CANOPY
INSTRUCTIONS
A
15/16”9/16”
5/16” to 13/32”
1/8 - | 1/4” |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| 5/16” |
|
|
|
|
|
|
| |||||
| 9/16” |
|
|
| |||||||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
USEUSE
(ORDER SEPARATELY)
6087
USEUSE
(ORDER SEPARATELY)
6088
(SUPPLIED)
B
C
CAUTION:
•TURN OFF POWER AT FUSE BOX BEFORE INSTALLING TRACK.
•DO NOT MAKE ELECTRICAL SPLICES IN OUTLET BOX OF GRID CEILING CANOPY KIT.
•USE SOLID 12 AWG WIRES FOR SUPPLY TO TRACK (NOT STRANDED).
•INSTRUCTIONS FOR GROUNDING MUST BE FOLLOWED. FAILURE TO DO SO MAY RESULT IN AN ELECTRICAL HAZARD.
A.INSTRUCTIONS
1.Remove appropriate VERTICAL K.O.’s for
2.Attach a bare or green color insulated 12 AWG solid copper GROUND WIRE approximately 8” long to the OUTLET BOX using the GROUND CLIP (supplied). Position GROUND CLIP as shown in Fig. 2. Bend wire so unattached end is pointing away from the OUTLET BOX. (Fig. 3).
3.Remove K.O. from top of OUTLET BOX and fasten an electri- cal connector (by others).
4.Place OUTLET BOX on
5.Pass SUPPLY LEADS through electrical connector leaving approximately 8” of wire beyond the box. WIRES MUST BE DRESSED AS SHOWN. (Fig. 4)
6.Fasten 12 AWG solid SUPPLY GROUND WIRE to OUTLET BOX using a GROUND CLIP (supplied). Position 180° from other GROUND CLIP. (Fig. 2)
| FIG. 1 | OUTLET |
|
| BOX |
|
| |
|
| VERTICAL KO |
|
| RECTANGULAR |
| CROSSBAR | KO |
GROUND |
|
|
WIRE |
|
|
|
| CANOPY |
|
| SPACER |
|
| BOTTO M |
| FEED TRACK OR | COVER |
CANOPY | CONNECTOR | THIN HEAD |
PLATE |
| SCREW |
® |