I
/ | INSTRUCTION SHEET NO |
|
INSTRUCTIONS FOR AITACHING LYTESPOV | IS:7637AZ | ||
TO LYTESPAN” TRACK | |||
|
| ||
| R0490 | Page 1 of 2 | |
FOR USE WITH LYTESPAN@ TRACK SYSTEMS ONLY. |
|
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for reference.
Ar
LYTESPAN TRACK
INSTRUCTIONS FOR AITACHING LYTESPOP TO SINGLE CIRCUIT TRACK
1.Align BEAD on L~ESPAN TRACK and GROOVE in FITTING before inserting into LWESPAN TRACK. See Fig. 1. (If BEAD is NOT aligned, a potential hazard may result.)
2.Unscrew the TURN KNOB partially and position LEVER. See Fig. 1.
3.To attach FITTING, squeeze BUITON and KNOB, insert into LWESPAN TRACK, and release. Tighten TURN KNOB. This holds FllTING to LYTESPAN TRACK mechanically. To energize turn LEVER ail the way until LEVER is parallel to LYTESPAN TRACK. See Fig. 2.
4.To shift fixture location on the LYlESPAN TRACK loosen TURN KNOB slightly, release LEVER and slide to new positon.
5.To remove fixture reverse the procedure in (3), push TURN KNOB in and allow FllTING to disengage.
6.Fixture can be left on LYTESPAN TRACK when not in use by turning LEVER to disconnect elect rically.
INSTRUCTIONS FOR CONVERTING
LWESPOV Attachment FllTING ~
OPERATE ON 2 CIRCUIT TRACK
NOTE: To insure proper operation of fixture on Two Circuit Lytespan Track, the BLACK SPACER (provided) must be used at all times on the plug assembly.
The BLACK SPACER is not used when operating Lytespots on Single Circuit Track.
LOWER CIRCUIT, FIG. 3:
Illustrates contacts in low position with spacer in place for lower circuit.
UPPER CIRCLflTj FIG. 4 and 5:
To convert attachment fitting for upper cir- cuit, raise BRASS CONTACT to high posi- tion (as indicated by dotted line) by pulling CONTACT as high as stop permits and slip ping on BLACK SPACER as shown in Fig. 4 and 5.
w’vTuRNKNoB
BEAD
GROOVE
FITTING
[ | FIG. 1 | IJ |
BUTT
|
|
| U | FIG. | 2 | ~ |
|
|
|
| MOVABLE BRASS |
|
|
|
| ||
|
| CONTACT |
| IC |
| ‘LACK | SPACER | |
|
|
|
| o |
| D |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| ~ |
|
|
|
|
|
| c |
|
|
|
|
|
|
|
|
| FIG. | 3 |
|
|
— | MOVABLE | BRASS |
|
|
|
| ||
|
| CONTACT |
|
|
|
|
|
|
|
|
|
| STATIONARY | SILVERED |
|
| |
BLACK |
|
|
| CONTACT | (COMMON) |
|
| |
\L |
|
|
|
|
|
|
| |
SPACER | . |
| PLUG |
|
|
|
| |
|
|
| ASSEMBLY |
|
| BLACK | ||
| ,+7” |
|
|
|
|
| ||
|
|
|
|
|
|
| SPACER | |
~~% | ,. |
|
|
|
| ,,.~..i |
| ) .~~% |
I |
| i |
|
|
| ‘“’~””’’”,’%:’,’;g- | ||
|
|
|
|
| \ |
| ||
|
|
|
| “=%~,,,,,~h$ | ||||
‘+’ |
|
|
|
| I‘ . “Y 7T | |||
FIG. 4 |
|
|
|
|
| ~’ | ||
|
|
|
|
|
|
|
| |
|
|
|
|
|
| .. ~~... |
| ,’ |
|
|
|
|
|
|
| ||
|
|
|
|
|
| FIG. | 5 |