Lightolier 8031 Page 2 of, FOR OPEN WALL WASHER 6132 Series Only, Instruction Sheet Number IS

Instruction Sheet Number  IS:8031

Page 2 of 2 Installation of Calculite® Compact Fluorescent Downlights and Wall Washer Reflector Trims

INSTALLATION OF LENS WALL WASHER AND OPEN WALL WASHER

Note: Before installing Reflector, make sure the Mounting Frame is installed with the Junction Box away from the wall to be illuminated (FIG. 9 & 9A).

FOR OPEN WALL WASHER (6132 Series Only)

1.Remove two Retaining Springs that are near the Junction Box from the Mounting Frame (FIG 10).

2.Insert two new Retaining Springs (that are provided with the reflector trim) into pockets on the Mounting Frame (FIG. 10A).

3.Squeeze Retaining Spring into position with pliers (FIG. 10A)

Wall to be Illuminated

Junction Box

Junction Box

From

(Positionedp awayAway from wallWall)

Lensed WallWasher

Lens Wall

Fig. 9

FOR OPEN WALL WASHER (N/S 6132 Series)

1.By hand, bend the 2 retaining springs that are near the junction box as far back as possible pushing toward J Box.

A. INSTALL WHITE TRIM RING (FIG. 1, 2, 3 & 4)

NOTE: Omit this section if reflector is self-flanged.

1.For overlapping trim installation (FIG. 1) slip White Trim Ring over Reflector, as shown in Fig 2 & 3.

2.For flangless trim installation (FIG. 4), White Trim Ring is

not required.

Wall to be Illuminated

Junction Box Junction Box (Positioned Away (positioned away Fromfrom wallWall)

Open Wall Washer

Open Wall Washer

Fig. 9A

B. SNAP-IN (FIG. 5)

Engage Retaining Spring into Slots in Reflector (see FIG. 5) following chart below. See Frame-in kit for lamp information.

C. PUSH-UP REFLECTOR (N/S 6132 Series)

1.Tilt Reflector so only (1) Retaining Spring (retaining spring closest to junction box) touches the Kick Reflector. Push reflector up to clear larger portion of Kick Reflector past the retaining springs and twist into positon.

LENS WALL WASHER

1.Tilt Reflector and insert Socket Cup into ceiling opening on side opposite Junction Box. Push Reflector up leaving approximately one inch of the Reflector exposed below the Ceiling Line (FIG. 11).

2.Compress Torsiontite Springs on Lens Trim by squeezing with fingers. Insert into Slots in Reflector and push up until flush with ceiling (FIG. 11).

NOTE: To remove Reflector, lift Lens and pull Lens Trim down (FIG. 12). Disengage the Socket Cup by depressing the Retaining Spring (FIG. 5). Turn Reflector counterclockwise while pulling downward. After starting, use both hands to remove (FIG. 7)

OPEN WALL WASHER

1. Tilt Reflector and insert Socket Cup into ceiling opening on side

opposite Junction Box. Pivot Reflector and push it up into ceiling

(FIG 6).

NOTE: To remove Reflector, disengage the Socket Cup by depressing

the Retaining Spring (FIG. 5). Turn Reflector counterclockwise while

pulling downward. After starting, use both hands to remove, see FIG 7.

D. LAMPING (FIG. 8)

NOTE: See Socket Cup Label for lamping information.

Line up Lamp Pins with Socket, tilt lamp base to engage, then bring

Retaining Spring

Retaining Spring

Removed

Removed

JunctionJunction Box Box

Socket Cup

Slot

Reflector

Wall to be Illuminated

Mounting

Framee

Fig. 10 Fig. 10A

Junction Box Junction Box (PositionedpawayAway Fromfrom wall)Wall)

Leave approx. 1" exposed

Lens Trim

w/ Torsiontite Spring

Fig. 11

Lamp to horizontal position and push into Socket (FIG. 8). To relamp,

CAREFULLY PULL STRAIGHT OUT OF SOCKET WITH ONE FINGER

PLACED ON THE TOP OF THE LAMP.

Fig. 12

CARE AND MAINTENANCE OF ALZAK REFLECTOR

See page. 1

Lightolier a Genlyte companywww.lightolier.com 631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710 We reserve the right to change details of design, materials and finish.

© 2006 Genlyte Group LLC • B0306