Lightolier 9279 instruction sheet Instructions for Lamping a Suspended

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE	INSTRUCTION SHEET NO.
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.	IS: 9279
To assure full compliance with local codes and regulations, check with your local electrical inspector
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.	A0101	Page: 4 of 4

INSTRUCTIONS FOR LAMPING AND OPERATING A SUSPENDED PowerWashTM T5 LUMINAIRE.

INSTRUCTION SHEET NO.		READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
IS: 9279		This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
		To assure full compliance with local codes and regulations, check with your local electrical inspector
		before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
A0101	Page 1 of 4	Retain these instructions for maintenance reference.

INSTRUCTIONS FOR ATTACHING SUSPENDED PowerWashTM T5 SUSPENSION HOUSING TO A LYTESPAN TRACK SYSTEM. FOR USE WITH LYTESPAN TRACK SYSTEMS ONLY.

INSTRUCTIONS FOR LAMPING A SUSPENDED	LAMPS	SOCKETS
PowerWash T5 LUMINAIRE:	SOCKETS
WARNING: USE PROPER WATTAGE T5 HIGH OUTPUT LAMPS ONLY.
SEE LABEL ON LUMINAIRE FOR PROPER WATTAGE.

NOTE: Not for use with ProSpec Track.

INSTRUCTIONS FOR ATTACHING SUSPENDED PowerWash

T5 SUSPENSION HOUSING TO LYTESPAN TRACK:

WARNING: TO PREVENT ELECTRIC SHOCK, TURN OFF

POWER TO TRACK. NEVER PLACE AIRCRAFT CABLE

INSIDE TRACK CAVITY (see Fig. 3).

1"	WARNING	TRACK
	LABEL
	CABLE LOCK

BEAD

		SOCKET
1.	Turn off power to track.	BRACKET
		Fig. 21
2.	Remove LOUVER (see Page 3).

3.Slide out both SOCKET BRACKETS (see Fig. 21). No tools required. Pull with hands.

4.Insert LAMP into SOCKET and rotate LAMP 90fl locking it

5.	in place.	SOCKET
	For two LAMP luminaire, repeat step 4 for the second LAMP.
		BRACKET
6.	Push SOCKET BRACKETS back into their original position

(see Fig. 22).

7.To remove LAMP, repeat steps 1-3. Rotate LAMP(s) 90fl and remove from SOCKET.

1.Remove WARNING LABEL on SUSPENSION HOUSING. See Fig. 1.

2.Unwrap AIRCRAFT CABLE. While depressing CABLE LOCK, pull AIRCRAFT CABLE through, leaving approx 1" above CABLE LOCK. See Fig. 1.

3.Insert SUPSENSION HOUSINGS into TRACK with ARROW on bottom of HOUSING pointing toward BEAD on TRACK. See Fig. 2.

4.Rotate SUSPENSION HOUSINGS 90fl clockwise. See Fig. 2.

5.Adjust suspension length and leveling by pulling AIRCRAFT CABLES through CABLE LOCK. See Fig. 3.

NOTE: To lower luminaire, hold CABLE, depress CABLE LOCK, and pull CABLE down. See. Fig 3.

AIRCRAFT	Fig. 1
CABLE	TRACK
	CAVITY	ARROW
PULL TO
RAISE

	SUSPENSION
Fig. 2	HOUSING

HOUSING BODY

HOUSING

NOTE: A two lamp luminaire will not operate with only one lamp. Assure that both lamps are properly installed. Also, both lamps will extinguish when one fails.

Fig. 22

6.If future suspension length adjustment is desired, up to two feet of AIRCRAFT CABLE can be wrapped around HOUSING BODY and pinned down using HOUSING SLOTS as shown in Fig. 4. If no adjustment will be desired, cut AIRCRAFT CABLE leaving approx 1/2" above CABLE LOCK. Crimp COPPER STOP (provided) onto AIRCRAFT CABLE. See Fig. 5.

WARNING: If Mounting on wall or sloped ceiling, COPPER STOP must always be used

7. Slide up HOUSING COVER and snap onto SUSPENSION

HOUSING as shown in Fig. 6.

HOLD THIS

CABLE; DEPRESS Fig. 3

LOCK TO LOWER

TRACK

COPPER

STOP

CORD

HOUSING

COVER

Fig. 4

SLOTS

AIRCRAFT CABLE

CORD

CORD RETAINER

AIMING INSTRUCTIONS (see Fig. 23)

CAUTION: ALLOW TIME FOR LUMINAIRE TO COOL BEFORE MAKING ANY ADJUSTMENTS!

Rotate HEAD of luminaire to desired position. Luminaire has rotation stops (DO NOT FORCE LUMINAIRE PAST STOPS. DOING SO MAY CAUSE AN ELECTRICAL HAZARD). HEAD

8. To remove or reposition on track, rotate SUSPENSION

HOUSING 90fl counter clockwise. See Fig. 2.

NOTE: To reposition HOUSING, HOUSING COVER does not have to be removed.

INSTRUCTIONS FOR WIRING SUSPENDED PowerWash T5 POWER STEM:

WARNING: Do not attach POWER STEM BASE into TRACK PRIOR TO WIRING.

1.	Leaving slack, CORD length can be determined by bringing
2.	it up to the TRACK and cutting. See Fig. 7.
	If a CORD RETAINER is desired, two are provided. Pull

Fig. 5

Fig. 6

Fig. 7

Fig. 8

1 15/16"

3/4"

BLACK

WHITE

GREEN

rotates 360fl.

HEAD

Fig. 23

	CORD through RETAINERS and position where needed. A
	standard TIE WRAP (local hardware item) may also be used.
3.	If CORD RETAINERS are not used, cut off. See Fig. 8.
	Pull CORD through POWER STEM HOUSING. See Fig. 9.
4.	Strip CORD and WIRES to lengths shown in Fig. 9.
WARNING: Do not damage WHITE, BLACK, or GREEN insulation.
5.	Tie knot in CORD as shown in Fig. 9.
6.	Twist strands of wire together and form a "J" loop. See Fig. 10.
7.	Connect: GREEN WIRE to GREEN SCREW MARKED "GND"
	WHITE WIRE to SILVER SCREW
8.	BLACK WIRE to BRASS SCREW
	Fasten POWER STEM HOUSING to POWER STEM BASE
	using HOUSING SCREWS. See Fig. 10.

CORD	Fig. 9	WIRES
POWER STEM HOUSING
		BRASS SCREW
		(BLACK WIRE)
POWER STEM HOUSING		WIRES

Fig. 10

SILVER SCREW (WHITE WIRE)

3/4"

2 1/4"

GREEN "GND" SCREW (GREEN WIRE)

HOUSING SCREWS

POWER

STEM BASE

LIGHTOLIER a GENLYTE THOMAS company.

631 Airport Road, Fall River, MA 02720

LIGHTOLIER a GENLYTE THOMAS company.

631 Airport Road, Fall River, MA 02720