READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE | INSTRUCTION SHEET NO. | |
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations. | IS: 9279 | |
To assure full compliance with local codes and regulations, check with your local electrical inspector | ||
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding. | ||
Retain these instructions for maintenance reference. | A0101 | Page 2 of 4 |
|
|
INSTRUCTIONS FOR ATTACHING SUSPENDED PowerWashTM T5 POWER STEM TO A
LYTESPAN® TRACK SYSTEM. FOR USE WITH LYTESPAN TRACK SYSTEMS ONLY.
TRACK POWER
INSTRUCTION SHEET NO.
IS: 9279
A0101 | Page 3 of 4 |
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding. Retain these instructions for maintenance reference.
INSTRUCTIONS FOR INSTALLING A PowerWashTM T5 LOUVER
NOTE: Not for use with ProSpec® Track.STEM LEVER
INSTRUCTIONS FOR ATTACHING SUSPENDED
PowerWash T5 POWER STEM TO SINGLE CIRCUIT
INSTRUCTIONS FOR INSTALLING A PowerWash T5
LOUVER:
TOP
SPRINGS
Fig. 17
LYTESPAN TRACK
BEAD
1. Turn off power to TRACK.
2. Insert POWER STEM into TRACK. The POWER STEM LEVER must be on the same side as the track BEAD. See Fig. 11.
3. Rotate POWER STEM 90fl clockwise using POWERPOWER STEM LEVER. POWER STEM LEVER should be parallel
1. | Turn off power to TRACK. |
2. | First insert BOTTOM SPRINGS on the LOUVER into the |
BOTTOM GROOVE in the luminaire (see Fig. 17 & 18). | |
3. | While pushing down TOP SPRING TABS, rotate LOUVER |
toward the TOP GROOVE in the luminaire until it hits the | |
FRONT STEP on the luminaire. Release the TOP SPRING TABS |
BOTTOM SPRINGS
with TRACK. See Fig. 12.
STEM
into the TOP GROOVE (see Fig. 17, 19, & 20). |
4.To remove: rotate POWER STEM 90fl counterclockwise using POWER STEM LEVER.
4. To remove, push down the TOP SPRING TABS and rotate |
away from the luminaire (see Fig. 19). |
SPRING TAB
INSTRUCTIONS FOR CONVERTING SUSPENDED PowerWash T5 POWER STEM ATTACHMENT FITTING TO OPERATE ON 2 CIRCUIT ADVENT LYTESPAN TRACK:
| Fig. 11 | Fig. 12 |
MOVABLE | BLACK |
|
BRASS | SPACER |
|
CONTACT |
|
|
NOTE: Ensure that all four LOUVER SPRINGS are fully engaged for safe operation (see Fig. 20).
NOTE: Luminaire may be used without LOUVER if desired.
Fig. 18
BOTTOM
SPRINGS
PLUG |
TOP
BOTTOM GROOVE
NOTE: To insure proper operation of PowerWash T5 suspension on Two Circuit Lytespan Track, the BLACK SPACER (provided) must be used at all times. The BLACK SPACER is not used when operating PowerWash T5 on Single Circuit Track.
LOWER CIRCUIT, Fig. 13 & 16:
Illustrates BRASS CONTACT in low position with BLACK SPACER in place for lower circuit.
UPPER CIRCUIT, Fig. 14, 15, & 16:
To convert power stem attachment fitting for upper circuit,
raise BRASS CONTACT to high position (as indicated by dotted line) by pulling CONTACT as high as stop permits and slipping on BLACK SPACER as shown in Fig. 14 & 15.
Do not try to move stationary silver contact.
U.S. PAT. PENDING
ASSEMBLY |
|
MOVABLE | STATIONARY |
BRASS | CONTACT |
CONTACT | (Neutral) |
Fig. 13
PLUG
ASSEMBLY
MOVABLE | BLACK | BLACK | |
SPACER | |||
BRASS | SPACER | ||
| |||
CONTACT |
|
|
Fig. 14
PLUG
ASSEMBLY
UPPER
CIRCUIT
Fig. 15 | LOWER | NEUTRAL |
| CIRCUIT |
|
Fig. 16
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
U.S. PAT. PENDING
GROOVE
FRONT STEP
LOUVER
Fig. 19
Fig. 20
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720