READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To

assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:C6E17OW

A0904

 

Page 1 of 1

INSTALLATION INSTRUCTIONS FOR 6" AND 7" RECESSED

EVOLUTION H.I.D. OPEN WALL WASHER DOWNLIGHT TRIMS.

CAUTION: (RISK OF FIRE) DO NOT INSTALL INSULATION ABOVE NOR WITHIN 3 INCHES (76mm) OF ANY

PART OF THE LUMINAIRE (LIGHTING FIXTURE)

CAUTION: USE ONLY ROUGH-IN SECTIONS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURERS’ ROUGH-IN KITS

WILL VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

LAMPHOLDER (supplied with frame)

LAMPHOLDER SPRING (supplied with frame)

REFLECTOR NECK

Fig. 1

Installing Lampholder onto Reflector (Fig. 1)

1.Bring LAMPHOLDER through frame opening into workspace.

2.Snap LAMPHOLDER SPRING into two slots on REFLECTOR NECK.

3.Check to make sure that both sides of LAMPHOLDER SPRING are fully engaged into slots.

4.Reflector trim is now ready for installation into ceiling.

Installing Reflector into Frame (Fig. 2) & (Fig. 3)

1.Feed assembled REFLECTOR into frame opening by aligning WINDOW CUT OUT between RETAINER SPRINGS. WINDOW CUT OUT must be opposite the wall to be illuminated as shown.

2.Push up on flange until it is fully installed into frame opening.

Re-lamping

1.To re-lamp one-piece units, simply unscrew the old lamp and replace with a new one. There is no need to remove trim from ceiling.

2.See trim labeling for correct lamp info. Follow lamp manufacturer's directions for proper care and handling of lamp.

RETAINER

SPRINGS

WINDOW

CUT OUT

Fig. 2

WINDOW

CUT OUT

WALL TO BE

ILLUMINATED

Fig. 3

**Care and Maintenance of “Alzak” REFLECTOR TRIM finish:**

If handling of REFLECTOR TRIM with anodized or Alzak finish is required, the use of clean white or plastic film gloves is recommended to avoid fingerprints.

Anodized or Alzak surfaces can be cleaned by the following methods:

1.Wipe off with a soft, clean, dry, lint-free cloth.

2.Wipe off with a soft clean cloth dampened in mild detergent solution. Rinse, then wipe dry with lint-free cloth or paper towel.

3.Wipe off with a clean cloth dampened with a solution of wetting agent and water (such as 2 oz. Per gallon “Pluronic L62-LF” by Wyandotte Products). Wipe dry.

4.Use a liquid wax such as Glass Wax. Avoid gritty cleaning agents.

A COMPANY

631 Airport Road, Fall River, MA 02720

Page 1
Image 1
Lightolier instruction sheet ISC6E17OW, Retain these instructions for maintenance reference, A0904

C6E17OW specifications

Lightolier C6E17OW is a remarkable lighting fixture that has become a staple in modern residential and commercial settings. This luminaire stands out due to its blend of functionality, energy efficiency, and stylish design, catering to a wide variety of aesthetic preferences.

One of the primary features of the Lightolier C6E17OW is its use of LED technology, which has revolutionized the lighting industry. LEDs are known for their longevity, with an average lifespan of up to 25,000 hours, making them a cost-effective and eco-friendly choice. The C6E17OW consumes significantly less energy than traditional incandescent bulbs, leading to lower energy bills and a reduced carbon footprint. This aligns perfectly with contemporary demands for sustainable living and energy conservation.

The design of the Lightolier C6E17OW is both sleek and versatile. Its neutral white finish and unobtrusive form allow it to blend seamlessly into various environments, from modern homes to commercial spaces. The fixture can be easily integrated into different styles of décor, whether minimalistic, industrial, or traditional.

Another key characteristic of the C6E17OW is its adjustable lighting. Users can modify the brightness levels to create the perfect ambience for any occasion. This flexibility makes it suitable for various applications, whether it’s illuminating a cozy living room, brightening a workspace, or enhancing the atmosphere in a dining area. The high Color Rendering Index (CRI) ensures that colors remain true and vibrant, which is particularly important in areas where accurate color representation is crucial, such as art studios or retail.

Further enhancing its appeal, the Lightolier C6E17OW incorporates advanced thermal management technology to maintain optimal operating temperatures. This ensures the longevity of the fixture and consistent performance over time. Additionally, its integrated dimming capability allows users to adjust light levels gradually, providing further customization options.

In conclusion, the Lightolier C6E17OW combines energy efficiency, stylish design, and advanced technology to offer a superior lighting solution. Its LED technology, adjustable features, and exceptional durability make it a wise choice for those seeking both practicality and elegance in their lighting choices.