Lighting Systems EC1-9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 1 of 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Energos Control System 2-Light T8 per 4' (121.92cm) (Nominal) Lens

Feature Specifications – Energos Control System (For standard Energos fixtures consult appropriate EG spec sheets)

Feature Specifications

Electrical

Dedicated low voltage (24 VDC) circuit controls the Energos Control Systems. The line voltage circuits control all the standard ballast functions including A/B switch- ing, Dimming and Emergency Battery Pack operations.

Occupancy Sensors:

Time delay is factory pre-set to 30 minutes.

Time delay can be field adjusted from 30 minutes to a minimum of 30 seconds.

Daylight hold-off is factory pre-set to 120 ft-candles (1291.67m-candles).

Daylight hold-off is field adjustable from 120 ft-candles (1291.67m-candles) down to 10 ft-candles (107.64m-candles).

Sensors are designed for a detection area (sensitivity diameter) of 16' (487.68cm) when suspended 10' (304.80cm) AFF. Lowering the sensor produces a smaller area of detection. See chart and diagram for additional information.

1. End Cap Sensor Mounting

2. Mid-mounted 8' (243.84cm)

 

Sensor Mounting

ECS occupancy sensors are available in two variations:

Mounted in the end cap.

The middle of an 8" (243.84cm) module.

The ECS system control-center is the Power Pack. The Power Pack, contained in each Master Module, interrupts the circuits when parameters dictate. The Power Pack can control up to 600 watts 120 VAC, and 1300 watts 277 VAC. A maximum of 10 sensors can be used on a single Power Pack. There is no limitation to the number of Power Packs that can be "daisy-chained" to a single ECS circuit.

Emergency battery packs can be used in conjunction with ECS for emergency egress lighting since all listed packs operate for a minimum of 90 minutes. EM Packs can be used as momentary lighting for emergency circuit for power transitions, and smaller packs are recommended for this purpose.

Coverage Diameter

16' 0" 14' 5" 12' 10" 11' 3"

Sensor Height AFF

7' 0"

8' 0"

9' 0"

10' 0"

Dimming ballasts can be used in conjunction with ECS. However, the control system will only perform ON or OFF operations and will not affect the level of dim- ming set by the dimming ballasts.

Factory installed ballast disconnect allows the ballast to be disconnected from and reconnected to incoming power under load without turning the entire circuit off.

Serial Row Linking (SRL) provides multiple continuous row communication. For every run that SRL is required, order the appropriate SRL end set from page 2 of this Specification Sheet. Consult Energos Application Guide for more detailed definitions and examples.

Mountings

Cable suspension distances are on 48" (121.92cm) and 96" (243.84cm) centers, and consist of a 4 1/2" (11.43cm) diameter canopy finished white enamel. A 1/16" (0.16cm) diameter stainless steel aircraft cable accomplishes suspension and is adjustable from 12" (30.48cm) to 36" (91.44cm). Power feeds are 18 gauge silver braided cord with clear jacket.

Energos Occupancy Sensor

Coverage Zone Chart

Height of Sensor

Broadcast Diameter

Task Diameter

10' 0" (304.80cm)

 

16' 0" (487.68cm)

8' 0" (243.84cm)

9' 0" (274.32cm)

 

14' 5" (427.99cm)

7' 3" (214.12cm)

8' 0" (243.84cm)

 

12' 10" (391.16cm)

6' 5" (184.15cm)

7' 0" (213.36cm)

 

11' 3" (336.04cm)

5' 7" (154.18cm)

 

 

 

 

Job Information

 

Type:

 

Job Name:

Cat. No.:

Lamp(s):

Notes:

631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710 We reserve the right to change details of design, materials and finish. www.lightolier.com © 2008 Philips Group • C0808

Page 1
Image 1
Lightolier EC1-9 specifications Feature Specifications Electrical, Coverage Diameter, Mountings

EC1-9 specifications

The Lightolier EC1-9 is an innovative lighting solution that stands out in the realm of modern architectural and commercial lighting. Designed with versatility and efficiency in mind, the EC1-9 series has become increasingly popular among architects and interior designers seeking to enhance spaces with a combination of functionality and elegance.

One of the primary features of the EC1-9 is its adjustable beam angle, enabling users to tailor the light distribution according to specific needs. This adaptability makes it suitable for a wide range of applications, from retail environments to office spaces and even art galleries. Users can achieve precise lighting effects, focusing attention on particular areas or providing ambient light for larger spaces.

The EC1-9 utilizes state-of-the-art LED technology, which drastically reduces energy consumption in comparison to traditional lighting solutions. With excellent energy efficiency ratings, the product supports sustainability initiatives while providing bright, consistent illumination. The LED source is also known for its long lifespan, reducing maintenance costs and the frequency of replacements—a key advantage in busy environments.

Another remarkable characteristic of the Lightolier EC1-9 is its sleek and modern design. The slim profile ensures that it seamlessly integrates into various decors without becoming an eyesore. This aesthetic appeal is complemented by the extensive range of finishes available, allowing designers to select fixtures that match their desired color palette and overall vision.

Moreover, the EC1-9 incorporates advanced dimming capabilities. This feature allows users to adjust the light intensity to suit different times of the day or activities, promoting comfort and enhancing the overall atmosphere of the space. This flexibility is particularly valuable in dynamic environments where lighting needs can shift frequently.

The EC1-9 also supports smart lighting technologies, enabling integration with existing building automation systems. This functionality facilitates remote management, allowing users to control and customize their lighting systems conveniently through smartphones or tablets. Such technological advancements position the EC1-9 as a forward-thinking choice for modern installations.

In summary, the Lightolier EC1-9 is a robust lighting solution characterized by its adaptability, energy efficiency, sleek aesthetics, and integration with smart technologies. With its ability to meet the diverse needs of contemporary architecture and design, the EC1-9 represents a significant advancement in the quest for optimal lighting solutions.