READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:1000IC

BO297

Page 1 of 1

INSTALLATION PROCEDURE FOR FRAME-IN KIT:

1000ICM, 1000AICM, 1100IC, 1100ICM,1100AICM, 1100DICM,1100DAICM

NOTE: I.C. Frame-in Kit may be used in direct contact with insulation.

1. FRAME-IN AND WIRE-IN

Line up bottom edge of ADJUSTABLE MOUNTING BAR with bottom of wood joist. (FIG. A). Fasten MOUNTING FRAME to wood joist by nailing MOUNTING BAR TAB or nail into joist. Wire to supply leads. White fixture lead to neutral supply lead. Black fixture lead to hot (120V.) supply lead. Bare fixture wire to supply ground. Use wirenuts (local hardware items.) Place all electrical con- nections in the J-Box. Attach J-BOX COVER onto J-Box. (Use built-in CABLE CLAMP in J-Box or non-metallic sheathed cable Romex.)

MOUNTING FRAME CENTERING SLOTS

ADJUSTABLE MOUNTING BAR

LINE UP BOTTOM EDGE WITH BOTTOM OF WOOD JOIST

NOTE: • Adjustable Mounting Bars can be installed either on long or short side of Mounting Frame (except for 1000AICM, 1100AICM, 1100DICM, and 1100DAICM). Locking screws provided to lock frame in a desired position.

•Mounting Bars can be extended to 24”. The Mounting Frame can be mounted off center. Align SLOT of one Mounting Bar with hole of the other Mounting Bar and drive screw into hole (not required for 1100DICM and 1100DAICM). Take pliers and bend tab on Mounting Frame over towards extended Mounting Bar until Mounting Frame no longer slides along Mounting Bars. (FIG.B) CENTERING SLOTS are provided as guides to align adjacent frames.

•For 1131 and 1133 series sloped ceiling trims, Mounting Frame must be mounted with J-BOX on the “uphill” side. Mounting Frame should be parallel to the joist. (FIG. C)

•For suspended ceiling, make certain that bottom of Mounting Frame is no longer than 1” above ceiling line, and notched area of Adjustable Mounting Bars are positioned on top of T-Bar. (FIG. D)

2. CLOSE-IN

Install plasterboard or other dry type ceiling. Hole in board can be cut either on floor or after the board is nailed to the ceiling, using Mounting Frame opening as cutting guide (make sure ROTO CLIPS are rotated out of hole area). Roto Clips can only be rotated counterclockwise. This detail allows easy removal of reflector trim by rotating TRIM counterclockwise and permits installing Reflec- tor Trim tightly against the ceiling surface by rotating trim clockwise after pushing Trim into ceiling.

NOTE: For 1000AICM, 1100AICM, and 1100DAICM apply a bead of silicone caulking compound between the ceiling opening and edge of fixture housing. For wet plaster ceiling, use plaster ring accessory No.1960 (order separately): No.1960 for 1000 series Frame-in kit, No. 1961 for 1100 series Frame-in Kit.

3.ATTACH SOCKET TO TRIM } SEE SEPARATE REFLECTOR TRIM INSTRUCTION SHEETS4. PUSH-UP

FIG.A

SCREW

TABS

MOUNTING FRAME

MOUNTING BAR

FIG.B

 

 

 

24”

 

WOOD JOIST

 

J-BOX

 

 

 

 

 

 

 

 

 

 

 

 

 

MOUNTING BAR

 

FIG.C

 

SOCKET CUP

 

 

 

 

 

 

 

 

 

 

 

 

11/2” MAX.

ADJUSTABLE

 

 

 

 

 

 

 

 

 

 

 

 

MOUNTING BAR

D1

D2

 

 

 

 

 

 

 

 

T-BAR

 

 

1” MAX.

 

 

 

Position notched areas of adjustable mounting bar on top of T-bar for proper spacing to finished ceiling. Lock mounting bars by bending tab underneath T-bar bead (FIG. D1), or use screw for round T-bar bead to lock bars, (FIG. D2)

FIG.D

WARNING: USE ONLY LIGHTOLIER REFLECTOR TRIMS MARKED WITH I.C. LAMPING INFORMATION.

WARNING: USE ONLY WITH TRIMS DESIGNATED BY LIGHTOLIER USE OF OTHER MANUFACTURERS’ TRIMS VOIDS THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

U.S. PATENT NOS. 4,313,514; 5,045,985

®

FALL RIVER, MASSACHUSETTS, 02720

MONTREAL, QUEBEC, CANADA

Page 1
Image 1
Lightolier IS:1000IC instruction sheet IS1000IC, Installation Procedure for FRAME-IN KIT, FRAME-IN and WIRE-IN, Close-In

IS:1000IC specifications

The Lightolier IS:1000IC is an innovative lighting fixture that stands out in the world of recessed downlighting. This product is designed to deliver superior performance while maintaining energy efficiency, making it an ideal choice for both residential and commercial applications.

One of the main features of the IS:1000IC is its Integrated LED technology. This allows for a longer lifespan compared to traditional incandescent or halogen bulbs. The LED technology not only contributes to durability but also significantly reduces energy consumption, offering a sustainable lighting solution. Additionally, the fixture provides high lumen output, ensuring bright and evenly distributed light across any space.

Another noteworthy characteristic of the IS:1000IC is its IC rating, which stands for Insulation Contact. This classification makes the fixture safe for direct contact with insulation, a crucial feature that enhances safety and energy efficiency in insulation-rich environments. This design ensures that the fixture can be easily installed in ceilings that are insulated, minimizing the risk of overheating and fire hazards.

The Lightolier IS:1000IC is also designed with versatility in mind. It is available in various color temperatures, ranging from warm to cool light options, allowing users to choose the ideal ambiance for their specific needs. The fixture is compatible with dimmer switches, providing further control over the lighting intensity, which can enhance the mood and functionality of a space.

Additionally, the fixture features a sleek, low-profile design that integrates seamlessly into most ceiling styles, maintaining aesthetic appeal. The easy installation process also makes it a popular choice among contractors and DIY enthusiasts alike. With a wide beam angle, the IS:1000IC ensures a broad light spread, effectively illuminating larger areas without creating harsh shadows or hotspots.

Durability is another strong point of the IS:1000IC. Constructed with high-quality materials, it offers resistance to corrosion and wear over time, making it suitable for various environments. This durability combined with low maintenance needs provides an excellent return on investment.

In summary, the Lightolier IS:1000IC offers an exceptional blend of energy efficiency, safety, versatility, aesthetic appeal, and durability, making it an outstanding choice for anyone looking to enhance their lighting experience. Whether in a modern home or a stylish office, the IS:1000IC is a brilliant solution that meets the needs of today's lighting demands.