Lightolier IS:1152-A ““’’’K’v%, Installation Of Lytecaster Reflector Trim, 151152.A

INSTALLATION OF LYTECASTER REFLECTOR TRIM

151152.A

IN THE 1102 FRAME-IN-KIT WITH ROTO CLIPS0690 Page2 of 2

TRIM lNSTALLATtON(Contd)

INSTALL LAMP

NmE Sooket manufactures have suggested that socket may fall after 3 to 6 ralampinge. If thla occurs sooket cart be replaced by dlaconnectlng male connectom (anached to socket Ieada) from female connectors (attached to flstura leads) and replacing it with a socket procured through Lightoller,

see Fig. L

INSULATING SLEEVING >	/	-	MA! F C.ONNHTCIRS
“..			{At~aci;di;”50CGt-tik.,

FEMALE CONNECTORS
(Attached to Fixture WE.)	MR16 SOCKET

FIG. I

7.	Remove	LAMP RING from	IAMPNOKE HOLDER by	““’’’K’v%
	GUARD	(Fig. K).
	pulling straight down (Fig. J),
8.	Insert LAMP (MR-16 Bulb)		between LAMP SPRINGS
	until face of bulb sits firmly on GLASS LAMP
9.	Attach	SOCKET to hi-pin	prungs on LAMP (Fig. K),
	(NUIT% No polarity of pins required).

10. Insert LAMP RING with LAMP and GLASS LAMP GUARD attached back into IAMPNOKE HOLDER.

G

VERTICAUANGLE ADJUSTMENT AND LOCK

11.Insert a screwdriver into the LOCKING GUIDE on the

LAMPNOKE HOLDER, and locate the slot in the

VERTICAL ADJUST/lQCK SCREW. turn the SCREW.

~–-’

FIG. J

counterclockwise+ and using the screwdriver as a ‘ lever, tilt the entire LAMP/’fOKE HOLDER to the desired angle. Once the desired angle is reached, tighten ecraw by turning screwdriver clockwise until snug tight.

HORIZONTAL ADJUST AND LOCK

12.The entire lAMP/YOKE HOLDER can be horizontally rotated to aim the angle of light through the hole in the FACE PLATE TRIM (Fig. K). This can be done by

racking off the HORIZONTAL ADJUST/~CK SCREW one full turn freein the SUPPORT PIATE (Fig. K). Grasping the YOKE 8 on either side of the LAMPNOKE HOLDER. rotate the SUPPORT PLATE to tha desired angle, and lock the poeition by tightening” the HORIZONTAL ADJUSWU3CK SCREW. Replete INSERTS

13, Insert PINHOLE FACEPLATE,

RELAMPING The locking mechanism in this fixture allow relamping without having to readjust and rslock. Follow Steps 7-10 and 13,

NOTE 1. LOW VOLTAGE FIXTURES should be dimmed only with speciai dimmers intended specifically for that purpose Use Lightolier Lytemodq Soeniat, Crsacendo VA, Neptune VA, Precision VA, Easyaet VA, Sunrise VA, Radiant VA or equlvalant products by others or variabie auto-transformera or eiactronic dimmers intendad for use with iow voltage fixtures. 2. Low voitage fisturas may produce audibie sound whan usad with dlmmere which may be objectionai in acouaticaiiy criticai areas.

WARNING: 1. LAMP MANUFACWRES REQUiRE THE GLASS LAMP GUARD BE IN PLACE BEFORE Energizing LAMR AND THAT GREAT CARE MUSr BE TAKEN THAT LAMP IS FULLY COOLED BEFORE RELAMP!NG. AVOID FiNGER MARKS ON INSIDE OF LAMP FOR THEY MAY CAUSE SHORT LAMP LIFE AND POSSIBLE BREAKAGE.

2. USE 0NL% REFLECIX)R “TRIMS PROViDED BY LiGHTOLIER INC. USE OF Uf’HER

MANUFA~URER’S REFLECTOR TRiMS VOIDS THE UNDERWRITERS LABORA~RIES LiSTING AND

‘ COULD Constitute A FIRE HAZARD.

J