READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:4X4

B0502

Page 2 of 2

B. ADJUST FIK

Set FIK so that bottom edge is flush to, or

ADJUSTMENT

ADJUSTABLE

SCREWS

MOUNTING

recessed 1/8” above finished ceiling (Fig. 8).

 

BRACKET

FIK

 

 

 

Final vertical adjustment may be made by means of

 

 

ADJUSTMENT SCREWS on inside of FIK.

 

 

C. CLOSE-IN

FLUSH TO CEILING OR

 

UP TO 1/8” RECESSED

 

Close-in and finish ceiling as required.

 

FINISHED

 

CEILING

 

 

FIG. 8

FIG. 9

Base of FIK is provided with a

hole pattern (Fig. 9) to assist with the alignment of multiple FIK’s. This hole pattern will facilitate the use of laser beams, plumb lines, etc.

D. INSTALLATION OF REFLECTOR TRIM

1.Squeeze both TORSION SPRINGS and insert ends into

EMBOSSED SLOTS.

2.Push REFLECTOR TRIM up into FIK until flange is seated firmly against ceiling surface.

**Care and Maintenance of “Alzak” REFLECTOR TRIM finish:**

If handling of REFLECTOR TRIM with anodized or Alzak finish is required, the use of clean white or plastic film gloves is recommended to avoid fingerprints.

Anodized or Alzak surfaces can be cleaned by the following methods:

1.Wipe off with a soft, clean, dry, lint-free cloth.

2.Wipe off with a soft clean cloth dampened in mild detergent solution. Rinse, then wipe dry with lint-free cloth or paper towel.

3.Wipe off with a clean cloth dampened with a solution of wetting agent and water (such as 2 oz. Per gallon “Pluronic L62-LF” by Wyandotte Products). Wipe dry.

4.Use a liquid wax such as Glass Wax®. Avoid gritty cleaning agents.

TORSION

SPRING

REFLECTOR TRIM

EMBOSSED

SLOT

FIG. 10

E. RE-LAMPING

1.

Turn off power

2.

Pull REFLECTOR TRIM down until ends of TORSION

 

SPRINGS reach EMBOSSED SLOTS.

3.

Squeeze TORSION SPRINGS to disengage from EMBOSSED

RELEASE SLOT

 

SLOTS, and remove REFLECTOR TRIM.

4.

Replace lamp (Do not exceed maximum wattage marking).

5.

Replace REFLECTOR TRIM.

 

 

 

F. BALLAST REPLACEMENT

1. Make sure AC power is OFF at fuse-box.

2. Remove REFLECTOR TRIM & lamp(s) (See E.).

3. Undo WINGNUT(s) and remove UPPER REFLECTOR.

4. Remove NUTS that secure BALLAST PLATE to HOUSING.

5. Partially remove BALLAST PLATE from HOUSING.

6.

Disconnect wire leads from BALLAST push-in terminals.

 

(Insert pin or paper clip in RELEASE SLOT, Fig. 11)

7.

Remove BALLAST from BALLAST PLATE, and install new

 

BALLAST.

NUTS

BALLAST

HOUSING

PLATE

 

 

FIG. 11

BALLASTBALLAST PLATE

8.

Insert wire leads into BALLAST°

. Follow wiring diagram on

 

90

 

 

BALLAST.

 

9.

Reattach BALLAST PLATE, UPPER REFLECTOR, lamp(s),

 

and REFLECTOR TRIM.

 

FIG. 12

WINGNUT

UPPER

 

REFLECTOR

A COMPANY

631 Airport Road, Fall River, MA 02720

Page 1
Page 2
Image 2
Lightolier IS:4X4 instruction sheet Adjust FIK, Close-In, Installation of Reflector Trim, Re-Lamping, Ballast Replacement
Page 1

IS:4X4 specifications

The Lightolier IS:4X4 is an innovative lighting solution designed to meet a variety of illumination needs in both residential and commercial settings. This fixture stands out for its sleek design, energy efficiency, and advanced technology, making it a preferred choice among architects, designers, and homeowners alike.

One of the main features of the IS:4X4 is its square-shaped housing, which offers a modern aesthetic suitable for a variety of installation environments. This design allows the IS:4X4 to be seamlessly integrated into ceilings, creating a clean and unobtrusive look. The fixture is available in multiple finishes and color temperatures, allowing for customization to match different interior decors.

The IS:4X4 employs advanced LED technology, which not only enhances illumination quality but also significantly reduces energy consumption compared to traditional lighting options. With a lifespan of over 50,000 hours, the LED modules minimize the need for frequent replacements, further contributing to lower maintenance costs. The fixture operates at high efficiency, ensuring bright and consistent light output while consuming minimal power.

Additionally, the Lightolier IS:4X4 features an adjustable lumen output, enabling users to tailor the brightness level to suit specific tasks or ambient requirements. This flexibility makes it ideal for various applications, including offices, retail spaces, and residential settings. The fixture also supports dimming options, allowing users to create the desired mood or atmosphere in any room.

The thermal management of the IS:4X4 is another noteworthy characteristic. Designed with a robust heat sink, the fixture effectively dissipates heat generated by the LED modules, ensuring optimal performance and longevity. This design helps maintain low operating temperatures, which contributes to the overall efficiency of the lighting system.

Furthermore, the IS:4X4 can be integrated with smart lighting controls, allowing for remote operation, scheduling, and energy monitoring. This capability enhances its usability in modern smart homes and commercial buildings, where energy management is a top priority.

In summary, the Lightolier IS:4X4 excels in delivering a combination of aesthetic appeal, energy efficiency, advanced technology, and flexibility. With its range of features, this fixture is well-suited for a wide variety of lighting applications, making it a valuable addition to any space.
Top Page Image Contents