r
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE | INSTRUCTION SHEET NO. | |
Thisfixtureis intendedforinstallationinaccordancewiththe NationalElectrical Code and load regulations. | IS:6079 | |
To assure full compliancewithlocalcodesandregulations,checkwithyourlocalelectricalinspectorbefore | ||
installation. Toprevent electrical shock, turnoff electricity at fuse box before proceeding. | ||
Retain these instructions for maintenance reference. | 0493 | Page 1 of 2 |
INSTALLATION FOR AITACHING EXTENSION WAND SLOPED CEILINGS ADAPTER
TO LYTESPAN TRACK. FOR USE WITH LYTESPAN” TRACK SYSTEMS ONLY
Extensionwandslopedceilingadaptercan be mountedon any Basic,Advent Multipointor MonopointTrackon tailings from 0° to 90° (vertical).
Notfor usewith Lytespota with attachmentfitting 7589.
1.Grasp TOP FITTING at top of ADAPTER and insert it into the LYTESPAN TRACK. The LOCKING LEVER must be on the same side of the track as the BEAD. (see Fig. 1.)
2.Rotate the TOP FI’ITING W’ clockwise, (See Fig. 2), untilLOCKING LEVER snaps and locks in plats. (See Fig. 3.) Do not rotate adapter from LOWER FllllNG.
3.Loosen KNOB and set the lower haff of the ADAPTER to a vertical positionand tighten KNOB. (Fig, 4)
4.To Remove Depress LOCKING LEVER; then rotate TOP FllllNG 90°
LOCKING |
| LVTESPAN |
|
| !l- | NG | |
| c |
|
| ||||
|
| TRACK |
|
|
|
|
|
BEAD |
| FITTING |
|
| riFIG. 3 | L |
|
|
|
|
|
| |||
LEVER |
|
|
| ‘“WERF’”’NI I I | |||
|
| CLOCKWISE |
|
| |||
FIG. 1 |
|
|
| FIG. 2 |
| FIG. 4 | |
INSTRUCTIONS FOR CONVERTING FITTING TO OPERATE ON |
|
| BRASS CONTACT | ||||
2 CIRCUIT TRACK SYSTEMS |
|
|
|
| |||
|
|
|
|
| |||
See Fig. 5, BRASS CONTACT can be raisedor lowered,Brokenlineindicatespositionfor 1 circuit |
|
|
| ||||
track or lower circuitof 2 circuittrack system. | - |
|
| L::;;:G | |||
BEAD |
| R/la“OWN |
|
|
| ||
To mnverf attachment FllTING for upper circuitof 2 circJJittrack, raise BRASS CONTACT to high |
|
|
| ||||
positionby Ming CONTACT as high as stop f.wrnits and CONTACT clicks into place. |
|
| FIG. 5 | ||||
INSTRUCTIONS FOR AllACHING EXTENSION WAND TO EXTENSION WAND SLOPED CEILING ADAPTER |
| ||||||
1. Insert the WAND FllllNG | into the LOWER FllllNG. |
|
|
|
|
| |
The LOCKING LEVER must be on the same side as the bead located at the bottom of the LOWER FllTING (See Fig. 6.) Rotate the WAND FllllNG | |||||||
90° clockwise until LOCKING LEVER snaps and locks in place. (See Fig. 6,7, & 8). |
|
|
| ||||
2, To remove, depress LOCKING LEVER and rotate FllllNG 90° counterclockwise. |
|
|
| ||||
| $ |
|
|
| i |
| |
|
| BRASSCONTACT |
|
|
|
| |
LOCKING_ |
| WAND |
| CLOCKWISE |
|
|
|
LEVER |
| FllTNG |
|
|
|
|
|
|
| 1 |
|
|
|
|
|
|
| FIG. 6 |
| FIG. 7 |
| FIG. 8 |