MULTISET/MULTISET PRO - MSCR/MHCR

Description

The MultiSet/Multiset Pro Channel Remote is a designer-style, full-function, multi-location remote device that uses existing three-way wiring to control MultiSet/MultiSet Pro dimmers or switches.

Channel Remotes use standard 3-way wiring. (see wiring diagram for details)

Features

Streamlined appearance and operations

A red LED light - to help locate the device in a dark room

As an individual device, the MultiSet/MultiSet Pro Channel Remote has the capability to recall two presets - a user-selected “on” level and full brightness.

When used with a MultiSet/MultiSet Pro Scene Master, the remote has additional applications - on/off, raise/lower and three way of a specific dimmer.

Caution

Caution: Be sure that power to the circuit being controlled has been disconnected by removing fuse or turning circuit breaker off. Installing device with power on may expose you to dangerous voltage and damage the device.

Installation Instructions

Note 1: If replacing an existing device with this device begin with Step #1 of Installation section.

Note 2: If installing this device in new construction begin with Step #4 of Installation section.

Reminder: Disconnect power at panelboard.

1.Remove faceplate from existing device.

2.Unscrew and pull device out of wallbox.

3.Disconnect wires from device. Using a wire box tester, identify and mark the “Hot” and the “Traveler” wires connected to device.

4.Install device per the following notes;

IMPORTANT!

4a. Be sure Multiset Ground wire (bare stranded) is connected to earth ground.

Note: Miswiring, or failure to connect ground, may result in improper operation of device.

Installation and

Operation

LED Indicator: (Fig. A)

Glowing RED = Power On (C)

Operating Instructions

TURN LIGHTS ON TO PRESET

• Tap rocker top once. (A)

TURN LIGHTS FULL-ON

Tap rocker top twice. (A)

ADJUST LIGHT LEVEL

Press and hold down rocker top or bottom until desired level is reached. (A or B)

• Release rocker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TURN LIGHTS OFF

 

 

 

 

 

 

 

• Tap rocker bottom once or twice. (B)

 

 

 

 

 

 

 

• Lights Fade off.

 

 

 

 

 

 

 

 

 

 

Note: When properly installed, the Red LED on the remote will be constantly

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. A

 

 

 

lit at half brilliance.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Wiring Notes

 

 

 

 

 

 

 

 

 

 

Multiset Remote to Wallbox Wire

 

 

 

 

 

 

 

Black

Hot (120V. Source, Must be same phase as dimmer)

 

 

 

 

 

 

 

Yellow

Traveler Wire from MultiSet/MultiSet Pro Dimmer On switch

 

 

 

 

 

 

 

Bare Copper

Earth Ground

 

 

 

 

 

 

 

*Grey

Ground or Neutral

 

 

 

 

 

 

 

* For Remote LED operation connect grey to neutral or ground

Note 1: MSCR/MHCR can control one MultiSet/MultiSet Pro Dimmer or switch from one or multiple locations.

Note 2: MSCR/MHCR must be wired on the same circuit as the device it is controlling.

Note 3: MSCR/MHCR provides manual override for any one device (channel) of a MultiSet/MultiSet Pro system

Note 4: Each circuit feeding dimmers and dimmed loads requires a separate neutral. Shared neutrals will result in undesirable flashing of controlled loads

Note 5: Line voltage must not be supplied by a GFI Breaker

Wiring Diagram

Note: No common neutrals on dimmed circuits.

4b. If using Compli faceplate (sold separately): Before connecting any wires, be sure the Compli faceplate mounting frame is behind the device with alignment tabs facing forward. Tabs should rest within centering holes of Remote’s aluminum mounting strap.

5.After all connections have been made (see wiring diagram and notes!) be certain all wire connectors are firmly attached.

6.Gently place wires and backbox into wallbox (with LED at top of device) and screw in place.

7.Before installing faceplate, restore power to circuit.

8.After testing device for proper operation, install faceplate onto the device.

Master MS-5

 

 

 

 

 

 

 

 

ON

 

 

 

 

 

 

 

 

A

B

120VAC

 

C

D

 

 

 

 

 

 

 

 

OFF

 

L

 

N

G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To Load

MS

L N

120VAC

To Load

MS

LN

120VAC

To Load

MS

 

R

 

 

 

N L

120VAC

2

3

Page 2
Image 2
Lightolier MHCR Description, Features, Installation Instructions, LED Indicator Fig. a, Operating Instructions