Manuals / Lincoln Electric / Power Tools / Welding System

Lincoln Electric 275 manual Service Procedures, Component Access, Spark GAP Adjustment

Models: 275

1 48
Download 48 pages 43.55 Kb
Page 31
Image 31

D-2

 

MAINTENANCE

D-2

 

 

 

 

SERVICE PROCEDURES

 

FIGURE C.1 SPARK GAP

Operation of the Precision TIG should be trouble-free for the life of the machine. Should a malfunction occur, however, the following procedures will be useful to trained service personnel with experience in repairing arc welding equipment:

.015 Spark Gap

COMPONENT ACCESS

The following components are accessible for routine set up and periodic service without requiring removal of the case sides or roof:

•Input Reconnect Panel (refer Section A) is located behind a removable panel on the rear of the left case side. Remove the two screws (with a screwdriver or a 3/8"/ 9.5mm hex driver) on the bottom corners of this panel to remove it.

•Control Box components and PC Boards (refer Section B Internal Set Up Controls) are located behind the front control panel. Remove the two screws (with a screwdriver or a 3/8"/ 9.5mm hex dri- ver) on the top corners of this panel to swing it down.

•Hi-Freq. Spark Gap assembly (refer Spark Gap Adjustment) is located behind a removable panel on the rear of the right case side, under the torch box. Remove the screw (with a screwdriver or a 3/8"/ 9.5mm hex driver) on the bottom center of this panel to remove it.

SPARK GAP ADJUSTMENT

The spark gap is set at the factory to a gap of 0.015 inches (0.4 mm) See Figure C.1. This setting is ade- quate for most applications. Where less high frequen- cy is desired, the setting can be reduced to 0.008 inch- es (0.2 mm).

WARNING

Use extreme caution when working with circuit of the high frequency. The high voltages developed can be lethal. Turn the input power off using the disconnect switch or fuse box before working inside the machine. This is particularly important when working on the secondary circuit of the high voltage transformer (T3) because the output volt- age is dangerously high.

------------------------------------------------------------------------

Note: In highly dirty environments where there is an abundance of conductive contaminants, use a low pressure air stream or a firm piece of paper to clean out the spark gap. Do not disturb the factory gap set- ting.

To check the spark gap:

1.Turn the input power off per above.

2.Remove the access panel on the right case side (See Component Access).

3.Check the spark gap spacing with a feeler gauge.

If adjustment is required:

1.Adjust the gap by loosening the Allen head screw on one of the aluminum blocks, reset the gap and tighten the screw in the new position.

If spark gap is correct:

1. Reinstall the access panel on the right case side.

PRECISION TIG 275

Page 30 Page 32
Page 31
Image 31
Lincoln Electric 275 manual Service Procedures, Component Access, Spark GAP Adjustment
Page 30 Page 32

275 specifications

The Lincoln Electric 275 is a versatile multi-process welding machine that stands out for its advanced features and robust performance. Designed for both novice and experienced welders, the machine offers MIG, TIG, and stick welding capabilities, making it a valuable tool for a variety of applications.

One of the main features of the Lincoln Electric 275 is its power output. With an impressive selection of amperage settings, it can deliver between 25 to 275 amps, making it suitable for both thin and thick materials. This flexibility allows users to work on projects ranging from automotive repairs to industrial fabrication.

The machine utilizes inverter technology, which significantly enhances its efficiency and reduces power consumption. Inverter welders are known for their lightweight design and compact size compared to traditional transformer-based welders. This portability makes the Lincoln Electric 275 easy to transport to job sites, catering to both professional and hobbyist welders who require mobility.

Another defining characteristic of the Lincoln Electric 275 is its easy-to-use interface. The digital display provides clear readings, allowing users to effortlessly adjust settings for optimal performance. Additionally, the machine features a user-friendly control panel with distinct knobs for regulating voltage and wire feed speed, assisting welders in achieving precise welds.

The Lincoln Electric 275 is also equipped with advanced arc technologies. Its built-in arc control enhances the stability of the welding arc, resulting in a smoother, more consistent weld. Furthermore, the machine offers synergic controls that automatically adjust the voltage and wire feed speed based on the selected material and thickness, making the welding process more intuitive and reducing the margin for error.

Durability is another hallmark of the Lincoln Electric 275. Constructed with high-quality materials, the machine is built to withstand the rigors of daily use in demanding environments. Its design also incorporates efficient cooling mechanisms to prevent overheating during prolonged operations, ensuring longevity and reliability.

In conclusion, the Lincoln Electric 275 is a powerful and adaptable welding machine that combines advanced technology with user-friendly features. Its multi-process capabilities, inverter technology, and robust construction make it an essential tool for both professional welders and DIY enthusiasts. Whether tackling intricate projects or heavy-duty tasks, the Lincoln Electric 275 proves to be a reliable choice that does not compromise on performance.