MAINTENANCE | ||
|
|
|
FUEL FILTER
1.Check the fuel filter and fuel
2.Replace the fuel filter if it is found with excessive water accumulation or sediment. Empty fuel
OVERSPEED IS HAZARDOUS
The maximum allowable high idle speed for this machine is 1890 RPM, no load. Do NOT tamper with governor components or setting or make any other adjustments to increase the maximum speed. Severe personal injury and damage to the machine can result if operated at speeds above maximum.
CLEANING THE BATTERY
Keep the battery clean by wiping it with a damp cloth when dirty. If the terminals appear corroded, discon- nect the battery cables and wash the terminals with an ammonia solution or a solution of 1/4 pound (0.1113 kg) of baking soda and 1 quart (0.9461L) of water. Be sure the battery vent plugs (if equipped) are tight so that none of the solution enters the cells.
After cleaning, flush the outside of the battery, the bat- tery compartment, and surrounding areas with clear water. Coat the battery terminals lightly with petroleum jelly or a
Keep the battery clean and dry. Moisture accumula- tion on the battery can lead to more rapid discharge and early battery failure.
ENGINE ADJUSTMENT
Adjustments to the engine are to be made only by a Lincoln Service Center or an authorized Field Service Shop.
CHECKING THE ELECTROLYTE LEVEL
If battery cells are low, fill them to the neck of the filler hole with distilled water and recharge. If one cell is low, check for leaks.
BATTERY MAINTENANCE | CHARGING THE BATTERY | |||||
When you charge, jump, replace, or otherwise con- | ||||||
To access the battery, remove the battery tray from | nect battery cables to the battery, be sure the polarity | |||||
the front of the machine with 3/8” nut driver or flat | is correct. Improper polarity can damage the charging | |||||
head screw driver. Pull the tray out of machine far | circuit. The VANTAGE® 400 (AU) positive (+) battery | |||||
enough to disconnect the negative and then positive | terminal has a red terminal cover. | |||||
battery cables. The tray can then be tilted and lifted to |
| |||||
remove the entire tray and battery from the machine | If you need to charge the battery with an external | |||||
for easy service. | charger, disconnect the negative cable first, then the | |||||
|
|
|
|
| positive cable before you attach the charger leads. | |
|
|
| WARNING |
| ||
|
|
|
| After the battery is charged, reconnect the positive | ||
|
|
| GASES FROM BATTERY can explode. | battery cable first and the negative cable last. Failure | ||
|
|
| to do so can result in damage to the internal charger | |||
|
|
| ● Keep sparks, flame and cigarettes | components. | ||
|
|
| away from battery. |
| ||
|
|
| To prevent EXPLOSION when: | Follow the instructions of the battery charger manu- | ||
|
|
| ||||
|
|
| facturer for proper charger settings and charging time. | |||
|
|
| ||||
| INSTALLING A NEW BATTERY — disconnect | |||||
● |
| |||||
| negative cable from old battery first and con- | SERVICING OPTIONAL SPARK | ||||
| nect to new battery last. | |||||
| ARRESTOR | |||||
● | CONNECTING A BATTERY CHARGER — | |||||
Clean every 100 hours. | ||||||
| remove battery from welder by disconnecting | |||||
| negative cable first, then positive cable and |
| ||||
| battery clamp. When reinstalling, connect | WARNING | ||||
| negative cable last. Keep well ventilated. | |||||
| • MUFFLER MAY BE HOT | |||||
|
|
|
|
| ||
●USING A BOOSTER — connect positive lead to battery first then connect negative lead to neg-
ative battery lead at engine foot. | • ALLOW ENGINE TO COOL BEFORE INSTALLING | |
THE SPARK ARRESTER! | ||
BATTERY ACID can burn eyes and | ||
| ||
skin. | • DO NOT OPERATE ENGINE WHILE INSTALLING | |
● Wear gloves and eye protection | ||
THE SPARK ARRESTER! | ||
and be careful when working near | ||
battery. | ||
| ||
● Follow instructions printed on battery. |
|
VANTAGE® 400 (AU)
