Lincoln Electric IM587-B manual Setting the DIP Switches, Wire Drive Head Selection

B-2 OPERATION B-2

Setting the DIP Switches

The DIP switches are each labeled with an “ON” arrow showing the on direction for each of the 8 indi- vidual switches in each DIP switch (S1 and S2). The functions of these switches are also labeled and set as described below:

Pwr Sources Head

				M 4 S R + -
ON		S1	ON		S2
	1 2 3 4 5 6 7 8			1 2 3 4 5 6 7 8

S1 S2

Wire Drive Head Selection

The LN-10 control is set up for proper presettable wire feed speed by setting S1 DIP switches (5 to 8) as appropriate per the following examples for the head specification and 10 Series wire drive external gear selection being used:

For K1563-1,-3 or K1564-Series (LN-10 Boom) or K1559-1 (LN-10 Bench) with 35-500 IPM (0.89-12.7 m/m) Low Speed Ratio set S1 DIP Switch as follows:

	Pwr Sources						Head
ON										S1
	1	2	3	4	5	6	7	8

S1

For K1563-1,-3 or K1564-Series (LN-10 Boom) or K1559-1 (LN-10 Bench) with 50-750 IPM (1.25-19.0 m/m) High Speed Ratio set S1 DIP Switch as fol- lows: (initial factory setting)

	Pwr Sources						Head
ON										S1
		1	2	3	4	5	6	7	8
S1

For K679-1 (Single Head Boom) with 50-770 IPM (1.27-19.5 m/m) Low Speed Ratio set S1 DIP Switch as follows:

	Pwr Sources						Head
ON										S1
	1	2	3	4	5	6	7	8

S1

For K679-2 (Single Head Boom) with 80-1200 IPM (2.00-30.5 m/m) High Speed Ratio set S1 DIP Switch

as follows:

	Pwr Sources						Head
ON										S1
	1	2	3	4	5	6	7	8

S1

Note: The K679-1and -2require the K1562-1control box.

Welding Power Source Selection

The LN-10 Control is set up for proper presettable weld voltage control by setting S1 DIP switches (1 to

4)as appropriate per the following information for the welding power source being used:

CV-250/CV 300-I:

Pwr Sources

ON									S1
	1	2	3	4	5	6	7	8

S1

CV-300/CV 400-I:

Pwr Sources

ON									S1
	1	2	3	4	5	6	7	8

S1

For K1563-2,-4 (LN-10 Boom) or K1559-2 (LN-10 Bench) with 55-825 IPM (1.40-21.0 m/m) Low Speed Ratio set S1 DIP Switch as follows:

	Pwr Sources						Head
ON										S1
		1	2	3	4	5	6	7	8
S1

For K1563-2,-4 (LN-10 Boom) or K1559-2 (LN-10 Bench) with 80-1250 IPM (2.00-31.8 m/m) High Speed Ratio set S1 DIP Switch as follows:

	Pwr Sources						Head
ON										S1
		1	2	3	4	5	6	7	8
S1

CV-400/CV 500-I:

Pwr Sources

ON									S1
	1	2	3	4	5	6	7	8

S1

CV-655:(initial factory setting)

Pwr Sources

ON									S1
	1	2	3	4	5	6	7	8

S1

V350-PRO And V450-PRO:

Pwr Sources

ON									S1
	1	2	3	4	5	6	7	8

S1

LN-10