Across the ARC SET-UPS, Figure A.5 | Lincoln Electric IM901-A

A-6	INSTALLATION	A-6

POWER SOURCE TO LN-25™ PRO

CAbLE CONNECTION DIAGRAMS

ACROSS THE ARC SET-UPS

CCPower Sources with Output Terminals Always Hot (See Figure A.5)

CCPower Source Ranger 250, 250 LPG

	Ranger 305G, 305D
	Commander 300
	Commander 300		FIGURE A.5
	Vantage 300, 400, 500
	Vantage 300, 400, 500
	Air Vantage 500		LN-25™ PRO
			LN-25™ PRO
	Ranger 10,000	Electrode
	Ranger 10,000		(Across the Arc)
			(Across the Arc)
	Ranger 3 phase
	SAE 400 with CV adapter			Work clip
				Work clip
	Engine Driven welder with	Work
	Wire Feed Module	Work
	Wire Feed Module

If the power source has a Remote/Local switch, place the switch in the Local position.

Place the CV/CC switch in the feeder in the "CC" posi- tion.

CV Power Sources with Stud Connectors and Remote/Local Switch (See Figure A.6)

K#	Description

K2613-1	LN-25™ PRO
K2613-2	LN-25™ PRO Extra Torque
KP1695-XX
KP1696-XX	Drive Roll Kit
KP1697-XX
See Magnum Literature	Welding Gun
	CC power Source
K1803-1	Welding Cables

FIGURE A.6

CV-655 DC-400 DC-600 DC-655 V450-Pro

Electrode

Work

LN-25™ PRO (Across the Arc)

Work clip

Place the power source Remote/Local switch in the Local position.

Place CV/CC switch in the feeder in the "CV" position.

K#	Description

K2613-1	LN-25™ PRO
K2613-2	LN-25™ PRO Extra Torque
KP1695-XX
KP1696-XX	Drive Roll Kit
KP1697-XX
See magnum Literature	Welding Gun
	CV power Source
K1803-1	Welding Cables

LN-25™ PRO ACROSS THE ARC MODEL

Image 13

Lincoln Electric IM901-A manual Across the ARC SET-UPS, Figure A.5

Contents

LN-25PRO Safety Depends on You California Proposition 65 Warnings Safety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosion Précautions DE Sûreté On-Line Product Registration Please Examine Carton and Equipment For Damage Immediately TAbLE of Contents Installation Location Safety PrecautionsHigh Frequency Protection Weld CAbLE SIzE Function Pin Wiring 3INSTALLATIONA-3CAbLE Connections Shielding GAS Connection Changing the GUN Receiver bUSHING Procedure to Install Drive Rolls and Wire Guides Loading Spools of Wire Pressure ARM AdjustmentGUN Connection Fe, CrNi Figure A.5 Across the ARC SET-UPS Figure A.7 Figure A.9 8INSTALLATIONA-8 Operation Definition of Welding Terms Recommended Power SourcesRecommended Processes Process Limitations Description Case Front Controls See Figure b.1Analog Voltmeter Wire Feed Speed, CV Operation Wire Feed Speed KNObMinimum Arc Volts Maximum WFS Extra Torque Polarity LED Figure b.2 Internal Controls Internal Controls Description CV/CC SwitchCold Feed PUSHbUTTON Figure b-3 Constant Current Wire Welding Rear Controls Itemdescription GAS Purge PUSHbUTTON POWER-UP SequenceFlow Meter Scfh Factory Installed Equipment AccessoriesWire Type Drive Roll Kits Accessories Kit Accessories K1500-5 Gun Receiver Bushing compatible Installation of the K590-6 Water Cooling KIT Routine Maintenance MaintenancePeriodic Maintenance CALIbRATION Specification To change the wire feed speed calibration See Figure D.2 Wire Feed Speed ValidationModel gearing BOARD Electric Shock can kill TROUbLESHOOTING Symptoms PRObLEMSFault Code Description Possible Adjustments POSSIbLE Output Problems TROUbLESHOOTING LN-25 PRO Across the ARC DiagramsModel Diagrams Dimension Print LN-25 PRO Across the ARC Model Precaucion Warnung