PCIe 1P (IEEE 1284)
User Manual | English |
www.lindy.com
0 | 13 | 0 | 1409 | 7168 Simple COMM. 10 |
|
|
|
| Controller |
If the Vendor ID, Device ID, Device Class or IRQ aren’t displayed or an error occurs, please try another PCI slot.
Once the hardware has installed correctly you can start installing the software from the driver CD.
Pin Assignments
Parallel 25 Pin female connector pin assignments:
Parallel 25 Pin female connector :
Pin | Signal | Pin | Signal | Pin | Signal |
1 | STROBE | 10 | ACKNOWLEDGE | 19 | GROUND |
2 | DATA 0 | 11 | BUSY | 20 | GROUND |
3 | DATA 1 | 12 | PAPER EMPTY | 21 | GROUND |
4 | DATA 2 | 13 | SELECT | 22 | GROUND |
5 | DATA 3 | 14 | AUTO FEED | 23 | GROUND |
6 | DATA 4 | 15 | ERROR | 24 | GROUND |
7 | DATA 5 | 16 | INIT | 25 | GROUND |
8 | DATA 6 | 17 | SELECT INPUT | 26 | GROUND |
9 | DATA 7 | 18 | GROUND |
|
|
Technical Specifications
•Support x17 x1,x2,x4,x8,x16 lane
•Operating system: DOS, WIN 9.x, ME, NT, 2000, XP, 2003 Server, VISTA, LINUX,
•Support ECP, EPP and SPP
•Ready of the Intel and AMD
•
•IRQ and IO address assigned by System
•Certified by Microsoft WHQL, CE, FCC approval
•PCB: 80 x 65 mm
Introduction
Thank you for purchasing the LINDY PCIe one Port parallel Card. This card is equipped with one 1284 centronics parallel interface.
The parallel port include IEEE1284 with speeds up to 15MB/Sec on the Parallel port.
Port Specification
Parallel Port:
•Chipset: Oxford 952
•IEEE standard: IEEE 1284 Interface
•Max. Speed: Up to 15MB/Sec
•DB 25 Female Connector
Package Contents
1 x LINDY PCI 1P Card
LINDY User manual
LINDY Driver CD
Installation
1.Turn off the power of your computer and remove the power cable
2.Install the PCI card into an available PCI slot in your computer
3.Connect the peripheral ie Printer, Modem, etc. to the adapters port
4.
PCI device listing display (for example…)
Bus | Device | Func | Vendor ID | Device | Device Class | IRQ |
No | No | No |
| ID |
|
|
0 | 7 | 1 | 8086 | 7010 | IDE Controller | 14 |
Certifications
FCC Certifications
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation.
CE Certification
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55024 and EN55022 class A for ITE,
Recycling Information
WEEE (Waste of Electrical and Electronic Equipment),
Recycling of Electronic Products
United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process.
Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways. Please follow your
