MOUNTING ON DOOR | MOUNTING ON WINDOW |
MOUNT PLATE
TO FRAME
1/2" MAXIMUM SPACE BETWEEN TRANSMITTER AND MAGNET PLATES
SNAP TRANSMITTER ONTO MOUNTING PLATE
ALIGN MAGNET PLATE NEXT TO TRANSMITTER PLATE AND ATTACH TO DOOR
MOUNT TRANSMITTER
PLATE TO FRAME
SPACE BELOW
PLATE IS REQUIRED
TO SNAP TRANSMITTER
ONTO PLATE
1/2" MINIMUM
SNAP TRANSMITTER ONTO MOUNTING PLATE
ALIGN MAGNET PLATE NEXT TO TRANSMITTER PLATE AND ATTACH TO WINDOW
OPTIONAL MAGNET SPACER
FOUR HEIGHT
POSITIONS
USE
SPACER WHEN MORE
HEIGHT IS REQUIRED
SQUEEZE SIDE TABS
TO ADJUST MAGNET
HEIGHT
HOOK SPACER TO
MAGNET PLATE
AND ROTATE TO
LOCK IN PLACE
OPTION JUMPER POSITIONS
SELECTS INTERNAL | SELECTS EXTERNAL |
SWITCH | SWITCH |
(INSIDE POSITION) | (MIDDLE POSITION) |
SELECTS GLASS | SELECTS BOTH | |
INTERNAL AND | ||
BREAK SENSOR ONLY | ||
EXTERNAL SWITCHES | ||
(EDGE POSITION) | ||
(NO JUMPER) | ||
|
NOTE: GLASS BREAK INPUT
TERMINALS ARE ALWAYS ACTIVE
CONNECTING EXTERNAL CONTACTS
WIRE EXTERNAL NORMALLY
CLOSED CONTACTS TO | THIS IS THE FACTORY SET | |
JUMPER POSITION IT SELECTS | ||
TERMINALS 1 & 2 | ||
THE INTERNAL SWITCH | ||
|
PUT JUMPER ON THE MIDDLE PINS TO USE EXTERNAL SWITCH
- OR -
CONNECTING EXTERNAL GLASS BREAK SENSOR
MOVE JUMPER FROM
THESE PINS (SELECTS
CONNECT NORMALLY OPENINTERNAL SWITCH)
GLASS BREAK SENSOR
WIRES TO TERMINALS 2 & 3
TO THESE PINS
(SELECTS GLASS
ROUTE SENSORBREAK SENSOR) WIRES UP THROUGH
WIRING SLOT
IMPORTANT NOTE: | TAKE JUMPER |
OFF TO USE | |
WHEN USING BOTH | BOTH |
INTERNAL AND EXTERNAL | EXTERNAL |
SWITCHES BOTH SWITCHES MUST | & INTERNAL |
BE CLOSED TO ARM THE TRANSMITTER | SWITCH |
NOTE: THIS TRANSMITTER IS DESIGNED FOR USE WITH THE UNITED SECURITY PRODUCTS "WINDOW BUG" GLASS BREAK SENSOR. OTHER SENSORS HAVE NOT BEEN TESTED.
CHANGING BATTERIES
WHEN BATTERIES ARE LOW, OPEN SENSOR CASE AND GENTLY LIFT UP END OF BATTERY CLAMP,
SLIDE BATTERIES OUT
NOTE: USE OF EXCESSIVE FORCE ON
BATTERY CLAMP WILL RESULT IN DAMAGE
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied.
For warranty service on Linear equipment return product, at sender’s expense to: Linear Corporation Repairs Department
LIFT
REMOVE BATTERIES
IF NECESSARYFROM THIS END PUSH IN SLOT TO REMOVE
SENSOR FROM MOUNTING PLATE
INSTALL TWO DURACELL TYPE DL 2032 BATTERIES (+)
SIDE UP
2580 Pioneer Avenue, Suite C
Vista, CA 92083
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless signalling. However, there are some limitations which must be observed.
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.
Changes or modifications to the device may void FCC compliance.
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.
Copyright © 1995 Linear Corporation | 211694 A |
