|
| DESCRIPTION |
SX | The | |
FORMAT! | ||
SUPERVISED |
| for applications such as door/window security. The |
| for alarms and restorals, low battery, status, tamper, and test. The | |
DIGITAL SECURITY | ||
supervised security receiver. | ||
TRANSMITTER |
| Coding switches are not required or used in the |
| is | |
|
| are more than sixteen million codes possible. |
|
| The |
Installation Instructions | with various types of external contacts, or both. When using one of | |
the internal contacts and the external input, both sensors must be | ||
|
| secured for a restore transmission, faulting either sensor will cause |
|
| an alarm transmission. External inputs can be either normally open |
|
| or normally closed. |
(760) | Switch selected options are included for glass break sensors, | |
pulse stretcher, battery saver, and external input type. | ||
USA & Canada (800) |
| |
Toll Free FAX (800) |
| |
STEP 1 Remove cover. Remove the | STEP 2 Remove battery protection strip. Pull the battery | |
cover by twisting a small screwdriver in the top slot (the fat | protection strip out from underneath the battery clamp. | |
end of the transmitter). |
| BATTERY |
|
| |
|
| PROTECTION |
|
| STRIP |
LIFT |
| PULL |
|
| STRIP TO |
|
| REMOVE |
| TWIST |
|
|
| 1 |
|
| 2 |
STEP 4 Pick transmitter location. Select a location for | STEP 5 Remove mounting plates. Use a small | ||
the transmitter. Avoid mounting the transmitter near the floor. | screwdriver to remove the transmitter’s mounting plate. | ||
Low level mounting can reduce transmission range and may | Squeeze the magnet’s tabs to remove its mounting plate. | ||
subject the transmitter to damage. Mounting the transmitter | IF USING EXTERNAL CONTACTS, SKIP TO STEP 8 | ||
on metal frame doors and windows is not recommended | SLIDE | ||
because the radio range will be reduced. | |||
MOUNTING | |||
MAGNET |
| PLATE OFF | |
TRANSMITTER | LIFT TAB WITH | ||
ON DOOR | |||
ON FRAME | SCREWDRIVER | ||
|
MAGNET ON |
| SQUEEZE |
WINDOW | EXTRA SWITCH FOR |
|
| ADJACENT WINDOW |
|
TRANSMITTER | EXTRA SWITCH |
|
ON FRAME | FOR WINDOW | REMOVE |
| NEXT TO DOOR |
|
The transmitter is powered by two
| TALL BATTERY | ADJUSTABLE |
| CLAMP FOR | |
| MAGNET | |
| BATTERIES |
|
| TRANSMITTER | MAGNET |
| SCREWS AND | |
| SCREWS AND | |
DOUBLE STICK TAPE | ||
TRANSMITTER |
| DOUBLE STICK TAPE |
|
|
STEP 3 Identify transmitter components. Examine the transmitter to identify the component locations.
OPTION | ANTENNA |
| BATTERY | TWO DL2032 | |
REDUCTION | OR CR2032 | ||||
| |||||
SWITCH |
| ||||
MAGNET |
| RING | BATTERIES | ||
|
| ||||
| ALIGNMENT |
|
| BATTERY | |
| MARK |
|
| ||
|
|
| CLAMP | ||
|
|
|
| ||
TEST/TAMPER |
|
|
| SCREW | |
|
|
|
| ||
SWITCH |
|
|
|
| |
|
|
|
| BATTERY | |
|
|
|
| CLAMP | |
EXTERNAL |
|
| INTERNAL | ||
|
| CONTACT | |||
CONTACT |
|
| |||
|
| DISABLE PINS | |||
TERMINALS |
|
| |||
|
|
|
| ||
WIRE | INTERNAL |
| MAGNET |
| |
CONTACT |
|
| |||
ENTRY |
| ALIGNMENT |
| ||
SIDE SELECT |
| ||||
SLOT | MARK |
| |||
JUMPER |
|
| |||
|
|
|
|
STEP 6 Select switch side. Place the internal contact jumper on the pins closest to the transmitter side on which the magnet will be.
|
| JUMPER TO LEFT |
|
| FOR MAGNET ON |
|
| THIS SIDE |
1 |
|
|
| 2 |
|
|
| 1 |
|
| 2 |
1 |
| JUMPER TO RIGHT |
| 2 | FOR MAGNET ON |
|
| |
|
| THIS SIDE |
|
| (FACTORY SETTING) |