II. GENERAL SAFETY RULES
Warning: When using electric tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury.
Read all these instructions before operating this product and save these instructions.
1) | Keep work area clean. | |||||||||
For saf operations: | ||||||||||
2) |
|
|
|
|
|
| environment. | |||
Consider work area | ||||||||||
| lutter d areas nd benches invi e injuries. | |||||||||
|
|
|
|
|
|
|
|
| ||
| Do not expose power tools to rain. Do not use | |||||||||
| power tools in damp or wet locations. Keep work | |||||||||
3) | area well lit. Do not use power tools where there | |||||||||
is risk of fire or explosion. | ||||||||||
Guard against electric shock. |
| |||||||||
4) | Avoid body contact with earthed or grounded | |||||||||
Keep children away. | ||||||||||
| surfaces e.g. pipes, radiators, ranges, refrigerators. | |||||||||
|
|
|
|
|
|
| ||||
5) | Do not let visitors touch the tool or extension | |||||||||
Store idle tools. | ||||||||||
| cord. Al visitors should be kept away from area. | |||||||||
|
|
|
|
|
| |||||
6) | When not in use, tools should be stored in a dry, | |||||||||
Do not forcethe tool. | ||||||||||
| high | r l ck d up place, out of reach of children. | ||||||||
|
|
|
|
| ||||||
7) | It will do the job better and safer at the rate for | |||||||||
Use the right tool. | ||||||||||
| whic | it was intended. | ||||||||
|
|
|
| |||||||
| Do not force small tools or attachments to do the | |||||||||
| job of a heavy duty tool. Do not use tools for | |||||||||
8) | purposes not intended; for example, do not use | |||||||||
ci cular saws to cut tree limbs or logs. | ||||||||||
Dress properly. |
| |||||||||
Do not wear loose clothing or jewelry, the can be caught in moving parts. Rubber gloves and non- skid footwear are recommended when working
outdoors. Wear protective hair covering to contain
9) Uselong safetyh ir. glasses.
Use face or dust mask if the cutting operation is
10) Dodustynot. abuse the cord.
Never carry the tool by the cord or yank it to
disconnect if from the socket. Keep the cord away
11) Securefrom heat,workoil. and sharp edges.
Use a vice to clamp the frame bar while adjusting blades. It is safer than using your hand and it frees both hands to operate the tools.
12)Do not overreach.
13)MaintainKeep propertoolfootingwith carend. balance at all times. Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubrication and changing accessories. Inspect tool cord periodically and if damaged have it repaired by an authorized service facility. Inspect extension cords periodically and replace, if damaged. Keep
14)Disconnecthandles dry,toolsclean. and free from oil and grease. When not in use, before servicing and when changing accessories such as blades, bits and
15)Removecutters. adjusting keys and wrenches.
Form the habit of checking to see that keys and adjusting wrenches are removed from the tool
16)Avoidbef re unintentionaltur ing it on. starting.
Do not carry a plugged in tool with a finger on the
17)Useswitchoutdoor. Ensurextensionswitch isleadsoff when. plugging in. When tool is used outdoors, use only extension
18)Staycordsalertinte.nded for outdoor use.
Watch what you are doing . Use common sense.
19)CheckDo notdamagedoper t toolpartswhen. you are tired.
Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operated properly and perform its intended function. Check for alignment of moving parts, free running of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated in this instruction manual. Have defective switches replaced by an authorized service facility. Do not use the tool if the switch does not turn it on and
20)Warningoff. .
The use of any accessory or attachment, other than those recommended in this instruction
21)Havem nual,yourmaytoolpresentrepaireda riskby ofa qualifiedpersonal personinjury. .
This electric tool conforms to relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts, otherwise this may result in considerable danger to the user.
3
