Loewe Spheros R 32, Spheros R 37 Programming recording for recorders, EPG menu, Data capture

Operating modes – EPG

In front of the programme’s title, the system places an ✓ . This station is switched later to this programme when the set is switched on. If the TV is off, it switches on again automatically at the beginning of the marked programme if this has been set in the EPG menu. If you are out, a security prompt prevents the TV set staying on unattended.

Before leaving the upper selection lines using the blue coloured key, select a specific line. If you have switched back to the programme list, you can change

this menu line using without having to leave the programme list.

Programming recording for recorders

The programme marked using the buttons can be prepared for recording by pressing the red coloured key. In the following menu, confirm the timer data or change them as required. Then, a red dot is set in front of this programme in the EPG programme list as an identification (if timer data is being transferred to the recorder, no red dot is set). If you select this programme, you can delete it from the timer using the red coloured key (if the timer data has been transferred to a recorder, the timer has to be deleted there).

EPG menu

	Call EPG menu
MENU
			INFO	END
		EPG menu
		Select provider OK	Station select Timer list Data capture	Switc

You will find the following settings in the EPG menu:

• Select provider • Station selection • Timer list • Data capture

• Switch on TV when marked

Selecting providers and stations

If you want to change the provider for analogue TV reception (the station which transmits EPG data) to have other stations evaluated, you can do this under "Select provider".

Select "Select provider" and call this menu using OK. If the station you want to switch to is not listed in the "Select provider" list, then use the yellow coloured key to start the automatic search for stations with EPG data. This takes a while.

Or, if you know the station that transmits EPG data, press the blue coloured key to compile manually. Select the provider in the station list and adopt it by using OK and return to the provider selection using .

Select the provider in "Select provider" and adopt it using OK. Then a station list search is performed. The stations offered by the provider are displayed in a list.

If you want certain stations to be omitted from the programme guide, you can select and deactivate these via Station selection. Call the station selection by using the blue coloured key.

First, all stations are marked with the ✓ symbol so that their data is displayed in the programme guide (precondition: provided EPG data is broadcast for the respective station). Stations indicated by E are analogue terrestrial/cable sta- tions, stations indicated by T are DVB-T stations, stations indicated by C are DVB-C stations and stations indicated by S are DVB-S stations. These stations are available for evaluation in the programme guide.

Select the stations you want to omit from the programme guide one after another and deactivate each one by using OK. The ✓ symbol is removed.

Data capture

After these settings or after each time the set is switched off using the mains switch, the data must first be collected, before switching on the set.

To do this, select the station you have defined as a provider and leave the TV set switched on for about one hour or switch the set to the standby mode. After about two minutes in standby mode, the orange indicator on the set lights up (for Spheros R 37, both indicators light up). The data capture begins and lasts about 1 hour. When data acquisition is terminated, the indicator turns red again. The data are also automatically captured between 2 a.m. and 5 a.m. when the TV is switched to standby.

A prerequisite for data capture is that "Data capture" is "on" (for DVB + ana- logue) in the EPG menu.

Note: If the TV set is switched off using the mains switch or the mains plug is pulled out, all EPG data are lost.

If, for example, you cannot receive any analogue EPG providers or if you only use DVB, you should set the data capture to "on (only for DVB)".

Switch on TV when marked

You can have the TV switched on automatically from standby at the beginning of the marked programme. If you are not present at the time, a safety prompt makes sure the TV switches off again after 5 minutes.

Downloaded From TV-Manual.com Manuals

- 28