2. Slip
the transducer's mounting pad between the bracket's mounting
"ears". Sandwich two internal lock washers between the transducer and
one side of the
mounting bracket as shown below. Place one washer on
the other side of the transducer.
11111
INSTALLATION
- Transom Mount
1. The transducer must be placed in a location that has a smooth flow of
water at all times. Air bubbles created
by
the movement of the
boat hull
against
the water interfere with the sonar
signal. This causes "noise" or random marks to appear on the sonar's display. You may need to
carefully
view the water's
path at the transom while the boat is moving to determine the best location for the transducer. 2. Make certain the chosen location doesn't interfere with the boat's
trailer. Mount the transducer at least one foot from the engine's lower
unit. This will prevent air bubbles from the transducer interfering with the
propeller.

LOWRANCE ELECTRONICS

FULL ONE-YEAR WARRANTY

'We", "our", or "us" refers to LOWRANCE ELECTRONICS. INC., the manufacturer
of this
product. "You" or
"your"
refers to the first
person who
purchases this product as a consumer
item for
personal, family,
or household use.
We warrant this
product against
defects or malfunctions in materials and
workmanship,
and
against failure to conform to this product's
written specifications, all for one
year (1)
from
the
date of
original purchase by you. WE MAKE NO OTHER EXPRESS WARRANTY OR
REPRESENTATION OF ANY KIND WHATSOEVER CONCERNING THIS PRODUCT.
Your remedies under this
warranty will be available so
long as
you
can show in a reasonable
manner that
any
defect or malfunction in materials or
workmanship, or
any
non-conformity
with the product's written specifications, occurred within one
year from the date of
your
original purchase, which must be substantiated by
a dated sales
receipt or sales
slip. Any
such
defect, malfunction, or
non-conformity
which occurs within one year
from
your original
purchase date will either be repaired without
charge
or be replaced with a new
product
identical or
reasonably equivalentto this product,
atour
option, within a reasonable time after
our
receipt
of the product If such
defect, malfunction, or
non-conformity remains after a
reasonable number of
attempts to
repair by us, you may elect to obtain without
charge a
replacementof
the
product ora refund forthe
product. THIS
REPAIR, REPLACEMENT,
OR
REFUND (AS JUST
DESCRIBED) IS THE EXCLUSIVE REMEDY AVAILABLE TO YOU
AGAINST US FOR ANY
DEFECT,
MALFUNCTION, OR NONCONFORMITY CONCERN-
ING THE PRODUCT OR FOR ANY LOSS OR DAMAGE RESULTING FROM ANY OTHER
CAUSE WHATSOEVER. WE
WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE
TO ANYONE FOR ANY
SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDI-
RECT DAMAGE OF ANY KIND.
Some states do not allow the exclusion or limitation of incidental or
consequential damages,
so the above limitations or exclusions
may
not
apply
to
you.
This
warranty
does NOT
apply
in
the
following circumstances: (1)
when the product has
been serviced or repaired by anyone other than us, (2) when the product has been
connected, installed, combined, altered, adjusted, or handled in a manner other than
according to the instructions fumished with the product, (3)
when any serial number has
been
effaced, altered, or
removed, or (4) when
any
defect, problem, loss, or
damage has
resulted from any accident, misuse, negligence, or carelessness, or from any
failure to
provide
reasonable and
necessary maintenance in accordance with the instructions of the
owner's manual for the product.
We reserve the right
to make changes
or
improvements in our
products
from
time to time
without
incurring the obligation to install such
improvements or
changes on equipment
or
items previously manufactured.
This
warranty gives you specific legal rights and you may also have other
rights
which may
vary
from state to state.
REMINDER: You must retain the sales
slip
or sales
receipt proving
the date of
your original
purchase in case
warranty service is ever
required.

LOWRANCE ELECTRONICS

12000 E SKELLY DRIVE TULSA,
OK
74128
(800) 324-1358
WASHER
WASHER
TWO WASHI
BOLT &
SLEEVE
3. Slide the metal sleeve over the bolt. Slip
the bolt and sleeve
through
the
bracket, washers, and transducer assembly. Place an internal tooth
lock washer over the end of the bolt and thread the nut onto it. Do not
tighten the nut at this time. The transducer is now ready for installation.
BOLT III 1111111111111111111111 I
6 47
PDF compression, OCR, web-optimization with CVISION's PdfCompressor