Lucent Technologies 362EC installation instructions Instructions below

PARTNER Endeavor Communications System Installation Instructions - Using a 2-Slot Carrier

IMPORTANT: To add a 362EC module to a PARTNER Endeavor system, the PARTNER Endeavor processor module must already be mounted on the wall. If it is not, refer to the PARTNER Endeavor Installation Guide for

instructions. Before starting, disconnect the power cord from the power jack in the carrier. Then follow the

instructions below.

1 A) Move the carrier’s On/Off switch to "Off," 2 and unplug the power cord from the wall outlet. B) To remove the cover, loosen the screw on lower front of the cover. C) Place one hand on the handle on the bottom front

of the cover, and place your other hand on the top of the cover. Gently pull the cover up and away from the carrier.

Before installing any modules, make sure the3 clear, plastic protector has been removed from the connector area on the rear of each module. To remove the protector, grasp the tabs on the ends of the protector and lift.

362EC

Processor

Module

A)Verify that the PARTNER Endeavor processor module is in the center slot of the carrier. In the other slots, from left to right, install the 362EC modules. B) Align the module carefully in the appropriate slot, and push slowly but firmly in the center of the module until the connectors on the module lock into place.

	362EC	362EC	ECS	362EC	362EC
	Module	Module	Proc.	Module	Module
	4	7	P F T	10	13
Line			1			Line
	5	8	2	11	14
Jacks						Jacks
	6	9	3	12	15
	18	26	P F T	34	42
			10
	19	27	11	35	43
	20	28	12	36	44
Extension	21	29	13	37	45	Extension
Jacks	22	30	14	38	46	Jacks
	23	31	15	39	47
	COMBO	COMBO	COMBO	COMBO	COMBO

! CAUTION:

Caution: Do not force the module. If the module does not insert easily, remove it, clear any obstruction, and reinsert it

4
5	7
6	8
		1
18	9	2	10
19		3	11	13
	26
20	27	10	12	14
21	28			15
22		11	34
	29	12	35
23	30	13	36	42
24				43
	31	14	37	44
25
	32	15	38	45
	33	16	39	46
		17	40	47
			41	48
				49

4 A) Label the lines and extension jacks. 5 B) Connect the line and telephone cords to the appropriate jacks on the new module.

C) Route each cord through the hook on the front of its module. D) Connect the free end of each phone cord to the modular wall jacks for system extensions. E) Connect the free end of each telephone cord to the modular connecting blocks for system extensions.

F) Gather the line and extension cords hanging below the hook and twist tie or wire wrap them. G) Place the bundle of wires in the indentation on the bottom carrier.

NOTE:

Connect ETR and T/R combination devices to the last two ports on the PARTNER Endeavor processor or 362EC module.

A)Plug the power cord into a properly grounded three-prong wall outlet not controlled by a switch. B) Power up the control unit by moving the On/Off switch to the "On" position.

6 Check the green lights on the fronts of the modules. If a single light is out, power down the carrier, then power up the carrier. If multiple lights are out, power down the carrier, reseat both modules, then power up the carrier. If the lights are still out, in the Continental U.S., call the hotline at

1-800-721-7071. Outside the Continental U.S., contact your Lucent Technologies Representative or local Authorized Dealer.

7 A) To replace the carrier’s cover grasp it by its upper edges and hold it squarely over the carrier. B) Place the cover over the modules and make sure it fits firmly in place. If it does not fit, make sure all modules are seated properly. C) Tighten the screw on the lower front of the cover.