Wiring Diagram - 240 volt
Wiring diagrams are provided here for reference purposes only. This information is also provided on schematics attached directly to the appliance on the left side.
Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dan- gerous appliance operation.
Outside Switches | Wall Switch | Wall Thermostat |
| ||
| (power on/off) |
|
L1 = Black (Power) |
|
|
|
|
|
|
|
|
|
|
| |
L2 = ORANGE (Power) |
|
|
|
|
|
|
|
|
|
|
| |
G = Green (Ground) |
|
| Control Panel |
|
|
|
|
|
|
|
| |
N = White (Common) |
|
| Control Panel |
|
|
|
| |||||
N1 = BLUE (Common) |
|
| Heater On/Off | (power on/off) |
|
|
|
| Control Panel | |||
N2 = BLUE (Common) |
|
| Switch |
|
|
|
| |||||
|
|
|
|
|
|
|
|
| Flame / Ember | |||
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| On/Off Switch |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |||
|
|
| Light (L) |
|
|
|
|
| . | |||
|
|
|
|
|
|
| SIP6 |
| ||||
GROUND |
|
| Flame Motor (L) |
|
| |||||||
|
|
|
|
|
| TEM. |
|
|
|
| ||
| N1 | Heater 2 (L) | REMOTE SIP2 | CircuitSIP4 |
|
| ||||||
|
|
|
| |||||||||
|
| N | Fan Motor (L) |
|
| SIP3 |
|
| LIGHT |
| ||
|
| N2 |
|
|
|
|
|
| SIP13 |
|
| SIP11 |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| Transformer |
MAIN POWER | N | L2 | Heater 1 (L) |
|
| Board |
|
|
|
| SIP7 | |
L2 |
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
| ||
HOME POWER | L1 |
| PTC |
|
|
|
|
|
|
|
|
|
SUPPLY |
|
|
|
|
|
|
|
|
|
|
|
|
240 VAC |
| L1 | T105° C |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Temperature Sensor
Figure 21 | Remote Sensor |
WIRING - 240 volt
See Power Supply Specifications on Page 3.
HOME POWER SUPPLY
240 VAC
120 V (L1) + 120 V (L2) = 240 V
The 120 volt power cord installed on this appliance MUST BE REMOVED (see instruction #2 on page 5).
Figure 22
N |
| WHITE | N |
|
|
|
| ||
L1 | 120 VAC | BLACK | L1 |
|
|
| FIREPLACE WIRE | ||
| 120 VAC | ORANGE |
| |
L2 | L2 | HARNESS | ||
| BLUE |
| ||
|
| N1 |
| |
|
| BLUE | N2 |
|
G |
| YELLOW AND GREEN | ground | |
|
| |||
ground | 240 v 3000 w |
|
WARNING
Do not install or operate this fireplace through a switch wired in the 120 VAC or 240 VAC circuits. The only approved wiring for a switch is through the low voltage circuit (24 VAC) as shown on Page 14.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
11
