Alt 3-4

MUTE/ALT 3-4 SWITCHES

Every time a bell rings, an Angel gets its wings. In a similar way, every time a mute switch is pressed,

that channel is muted in the main mix and

 

 

 

 

 

 

 

 

 

 

 

Alt 3-4 outputs

 

 

 

 

 

 

 

 

 

 

 

 

 

appears in the alt 3-4 outputs instead. Aux

 

 

 

 

 

 

 

 

 

 

 

 

 

sends 1-4 in post-mode (for external

 

 

 

 

 

 

 

 

 

 

 

 

 

processors) are also muted, but aux sends

 

 

 

 

 

 

 

 

 

 

 

 

 

1-4 in pre-mode (for stage monitors) are not

 

 

48V48V

48V

48V

48V

48V

48V

 

48V

 

 

Control Room/

muted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Phones Source

If you just want to mute the channels, then

 

 

 

 

 

 

 

 

 

 

 

 

Alt 3-4

 

 

 

 

 

 

 

 

 

 

 

 

Assign to Main

don't connect the alt 3-4 outputs to anything.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mix

 

 

 

 

 

 

 

 

 

 

 

 

 

Muted channels can still be soloed to

 

 

 

 

 

 

 

 

 

 

 

 

 

audition them in the headphones and control

 

 

 

 

 

 

 

 

 

 

 

 

 

room, and to adjust and check the channel

 

 

 

 

 

 

 

 

 

 

 

 

 

gain levels.

Mute/Alt 3-4

MUTE

MUTE

MUTE

MUTE

MUTE

MUTE

MUTE

MUTE

MUTE

MUTE

MUTE

MUTE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

switches

 

 

 

 

 

 

 

 

 

 

 

 

ALT 3-4 OUTPUTS

 

 

 

 

 

 

 

 

 

 

 

 

 

These 1/4" TRS jacks provide a balanced

 

SOLO

SOLO

SOLO

SOLO

SOLO

SOLO

SOLO

SOLO

SOLO

SOLO

SOLO

SOLO

line-level signal that can provide an alternate stereo mix for recording or subgrouping.

Connect these outputs to the inputs of an amplifier, powered speaker, or recording device. If you want to think up some good uses for the alt 3-4 outputs then go ahead.

For example, these outputs could be used to send particular channels to another zone, or you could create a sub-mix of several drum microphones. The alt 3-4 submix can then be routed to the control room and phones, by pressing the control room alt 3-4 switch, and then added to the main mix with the control room "assign to main mix" switch.

The alt 3-4 output doesn’t have a master level control. All the channels assigned to the alt 3-4 bus are summed together (post-fader and pan) and sent directly to the alt 3-4 out.

Quick Start Guide 13